manualshive.com logo in svg

Intel SE7221BA1, Техническое руководство

Поделиться
Скачать
Intel SE7221BA1 Скачать руководство пользователя страница 54

System BIOS 

Intel® Entry Server Board SE7221BA1-E TPS 

44  

Revision 

1.5 

 

7.10 Error Messages and Beep Codes 

7.10.1 

BIOS Error Messages 

Table 27 lists the error messages and provides a brief description of each. 

Table 27.  BIOS Error Messages 

Error Message 

Explanation 

GA20 Error 

An error occurred with Gate A20 when switching to protected mode 
during the memory test.  

Pri Master HDD Error  
Pri Slave HDD Error  

Could not read sector from corresponding drive. 

Pri Master Drive - ATAPI Incompatible Pri 
Slave Drive - ATAPI Incompatible  

Corresponding drive in not an ATAPI device.  Run Setup to make sure 
device is selected correctly. 

A:  Drive Error 

No response from diskette drive. 

Cache Memory Bad 

An error occurred when testing L2 cache.  Cache memory may be bad.

CMOS Battery Low 

The battery may be losing power.  Replace the battery soon. 

CMOS Display Type Wrong 

The display type is different than what has been stored in CMOS.  
Check Setup to make sure type is correct. 

CMOS Checksum Bad 

The CMOS checksum is incorrect.  CMOS memory may have been 
corrupted.  Run Setup to reset values. 

CMOS Settings Wrong 

CMOS values are not the same as the last boot.  These values have 
either been corrupted or the battery has failed. 

CMOS Date/Time Not Set 

The time and/or date values stored in CMOS are invalid.  Run Setup to 
set correct values. 

DMA Error 

Error during read/write test of DMA controller. 

FDC Failure 

Error occurred trying to access diskette drive controller. 

HDC Failure 

Error occurred trying to access hard disk controller. 

Checking NVRAM..... 

NVRAM is being checked to see if it is valid. 

Update OK! 

NVRAM was invalid and has been updated. 

Updated Failed 

NVRAM was invalid but was unable to be updated. 

Keyboard Error 

Error in the keyboard connection.  Make sure keyboard is connected 
properly. 

KB/Interface Error 

Keyboard interface test failed. 

Memory Size Decreased 

Memory size has decreased since the last boot.  If no memory was 
removed then memory may be bad. 

Memory Size Increased 

Memory size has increased since the last boot.  If no memory was 
added there may be a problem with the system. 

Memory Size Changed 

Memory size has changed since the last boot.  If no memory was added 
or removed then memory may be bad. 

No Boot Device Available 

System did not find a device to boot. 

Off Board Parity Error 

A parity error occurred on an off-board card.  This error is followed by 
an address. 

On Board Parity Error 

A parity error occurred in onboard memory.  This error is followed by an 
address. 

Parity Error 

A parity error occurred in onboard memory at an unknown address. 

Содержание SE7221BA1














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды