Intel is a registered trademark of Intel Corporation or its
subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property
of others. Copyright © 2014, Intel Corporation. All rights
reserved.
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the
Intel
®
Server Board and Server Chassis
Safety Information
document at:
http://support.intel.com/support/
motherboards/server/sb/cs-010770
.htm
for complete safety information.
Warning
Installation and service of
this product should only be
performed by qualified service
personnel to avoid risk of injury from
electrical shock or energy hazard.
Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Building Value with Intel
Server Products, Programs and Support
Get the high-value server solutions you
need by taking advantage of the outstanding
value Intel provides to system integrators:
For more information on Intel's added-value
server offerings, visit the Intel
®
ServerBuilder
website at:
www.intel.com/go/serverbuilder.
•
Worldwide 24x7 technical support
(AT&T Country Code + 866-655-6565)
1
•
World-class service, including a
three-year limited warranty and Advanced
Warranty Replacement
1
•
High-quality server building blocks
•
Extensive breadth of server building blocks
•
Solutions and tools to enable e-Business
•
Product information, including
product briefs and technical product
specifications
•
Sales tools, such as videos and
presentations
•
Training information, such as the
Intel
®
Online Learning Center
•
Support Information and much more
Intel
®
ServerBuilder is your one-stop
shop for information about all of Intel's
Server Building Blocks such as:
1
Available only to Intel
®
Channel Program
Members, part of Intel
®
e-Business Network.
For more information on the jumpers referenced in this diagram, refer to user guide located on the web at:
http://support.intel.com/support/motherboards/server.
1
Check the Bracket Height
Determine whether the full-height bracket will fit
in the server’s PCI back plate.
A
Your RAID controller ships with the full-height
bracket. If the low-profile bracket is required,
unscrew the two fasteners holding the green
board to the silver bracket.
B
Line up the low-profile bracket with the board,
making sure the two holes align.
D
Replace and tighten
the two screws.
E
Remove the bracket.
C
Full-height
Bracket
Low-profile
Bracket
2
Install the RAID Module
Power down the system and disconnect the
power cord.
A
Remove the system cover and any
other pieces to access the
PCI Express* slot.
B
C
D
PCI Express* Slot (3.3 V)
Firmly press the RAID module into an available
x8 or x16 PCI Express* Slot.
Secure the RAID module bracket to the system
back panel.
E
The Intel
®
Integrated RAID Module RMS25KB080
is shown for illustrative purpose.
What you will need to begin
•
SAS 2.0 or SATA III hard disk drives (backward compatible to support SAS 1.0 or SATA II hard
disk drives)
•
Intel
®
Integrated RAID Module RMS25KB080 or RMS25KB040 (SAS/SATA cables need to be
prepared separately)
•
SAS/SATA cable accessory kit, which can be ordered from Intel separately. Please see the Tested
Operating System List for available cable accessory kits at:
http://www.intel.com/p/en_US/support/server
•
Server board with a x8 or x16 PCI Express* slot (this controller is designed to meet the x8 PCI
Express* Generation 3 specification and is backward compatible with generation 2 or 1 slots)
•
Resource CD, which is shipped with systems or boards
•
Operating system installation media: Microsoft Windows Server 2003*, Microsoft Windows
Server 2008*, Microsoft Windows Server 2012*, Microsoft Windows 7*, Microsoft Windows Vista*,
Red Hat* Enterprise Linux, or SUSE* Linux Enterprise Server, VMware* ESX Server 4,
and VMware* ESXi5. Notes: The module will support PCI Express* Revision 3.0 at post launch.
This guide contains step-by-step instructions for installing
the Intel® Integrated RAID Module RMS25KB080 and RMS25KB040
and information on using the BIOS setup utility to configure a single logical
drive array and install the driver into the operating system.
These guides and other supporting documents
(including a list of supported server boards) are also located on the web at:
http://www.intel.com
For more advanced RAID configurations, or to install with other
operating systems, please refer to the Hardware User’s Guide.
Read all cautions and warnings first before starting your RAID Controller
integration.
If you are not familiar with ESD (Electrostatic Discharge) procedures used
during system integration, see your Hardware Guide for complete ESD
procedures. For more details on Intel® RAID controllers, see:
www.intel.com/go/serverbuilder.
Intel® Integrated RAID Module
RMS25KB080 and RMS25KB040
Quick Start User's Guide
*
Intel® Integrated RAID Module RMS25KB080 as shown
G42745-004
3
Connect the RAID Module
Connect the wide end of the cable to the up silver connector (ports
0-3).The Intel
®
Integrated RAID Module RMS25KB080 is shown for
illustrative purpose.
A
Push the cable into the silver connector until it makes a slight click.
B
If using more than four drives, connect the wide end of the second
cable to the down silver connector (ports 4-7).
C
Connect the other ends of the cables to SATA drives or to the ports
on a SATA or SAS backplane.
Notes: Both non-expander backplanes (one cable per drive) and
expander backplanes (one or two total cables) are supported.
Drive power cables (not shown) are required.
D
Rear view of four SATA drives or backplane connected to ports
on the Intel
®
Integrated RAID Module RMS25KB080.
A
B
C
D
D
Ports 4-7
(This connector is not available on
Intel
®
Integrated RAID Module RMS25KB040 )
4
Use the LSI MPT SAS BIOS Configuration Utility* to Create a RAID Virtual Drive
Note: As necessary, see “Choosing the Right RAID Level” on side 2 of
this Quick Start User's Guide for a brief description of RAID levels.
Power on the system and press <
Ctrl
> + <
C
> when the screen
below is displayed.
1
In the Adapter List Global Properties window select the controller in
the Adapter column and press <
Enter
>.
2
Highlight RAID Properties and press <
Enter
>.
3
On the Select New Array Type screen, select the appropriate configuration,
for example Create IM Volume, and press <
Enter
>.
4
Intel® Integrated RAID Module
RMS25KB080 and RMS25KB040
Reference Diagram
Bracket Screw(2)
J4A1 Ports 0-3
J4B1 Ports 4-7
(This connector is
not available on
Intel
®
Integrated
RAID Module
RMS25KB040)
x8 PCI
Express*
Interface
Front View
Back View
