background image

2

General Installation Process

1

Unpack the RMFBU4 Module

Unpack the RMFBU4 module in a static-free environment. Remove the 

module from the antistatic bag, and inspect it for damage. If the 

module appears to be damaged, contact Intel or your reseller support 

representative.

CAUTION: It is good practice to back up your data before 

adding hardware, such as an RMFBU4 module, to your 

system.

2

Prepare the Host Computer

CAUTION: Before you install the RMFBU4 module, make 

sure that the host computer is disconnected from the 

power and from any networks.

Turn off the host computer, and unplug the power cords from the rear 

of the power supply. Remove the cover from the host computer to 

permit access to the RAID controller.

3

Remove the RAID Controller from 
the Computer

A

Unplug all cables from the RAID controller, remove the screw that 

attaches the bracket to the computer chassis, and carefully remove 

the RAID controller from the slot.

B

Place the RAID controller on a flat, clean, static-free surface.

4

Attach the RMFBU4 Module to the 
RAID Controller

A

Ground yourself, and make sure that the system is grounded.

B

Place the RMFBU4 module front-side-up on a flat, clean, static-free 

surface.

C

Mount the two standoffs on the front side of the RAID controller by 

screwing in two screws from the back side of the RAID controller, as 

shown in the following figure.

The standoffs are threaded at both ends, and the screws thread from 

the back side of the RAID controller into the board-to-board 

standoffs.

Center the screwdriver carefully to avoid stripping the screw heads. 

Do not over-tighten the screws.

D

Hold the RMFBU4 module so that the front side faces upward, and 

align the J2 connector on the RMFBU4 module with the connector 

on the RAID controller.

E

Carefully press the RMFBU4 module onto the RAID controller so 

that the two connectors are firmly joined.

RMFBU4

J2 

Connector

J4B1

Connector

Intel

®

 RAID Controller 

RS3DC080 as shown

F

Secure the RMFBU4 module to the RAID controller by screwing in 

the two screws from the top side of the RAID controller.

The standoffs are threaded at both ends, and the screws thread from 

the back side of the RAID controller into the board-to-board 

standoffs.

Center the screwdriver carefully to avoid stripping the screw heads. 

Do not over-tighten the screws.

NOTE: If the Super Capacitor Pack module is to be attached to 

a remote mount board, continue to follow the steps 5 to 9. If 

the Super Capacitor Pack module is to be attached to an Intel

®

 

Server Chassis, continue to follow the steps 10 to 12. 

Содержание RMFBU4













Отзывы: