Intel PXA27x Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 88

background image

40

Intel

®

PXA27x Processor Developer’s Kit

- User’s Guide

2.3.6

JTAG Interface

Two JTAG connectors, the in-circuit emulation (ICE) connector and a stake pin header, provide the
interface for devices on the JTAG chain, such as the main board and Intel

®

PXA270 Processor

CPLDs, the main board FPGA, and the daughter card. For details of the JTAG interface, see

and the daughter card schematic diagram.

2.3.7

Logic-Analyzer Interface

lists the logic-analyzer connections on the daughter card. For pin assignments, see the

daughter card schematic diagram.

2.3.8

System Configuration Register

Pull-up and pull-down resistors built into the daughter card provide the system with the necessary
configuration information. For details of the System Configuration Register, see

“Virtual Configuration Registers” on page 50

.

2.3.9

Connectors

lists all of the connectors on the daughter card.

•

For the locations

of connectors on the daughter card, see

.

•

For descriptions

of a connector’s use, see the referenced section in this document.

•

For pin assignments

, see the daughter card schematic diagram.

•

To identify a connector’s type

, see the daughter card parts list.

Table 7. Connectors, Daughter Card (Sheet 1 of 2)

Designator

Name

J1

Reserved

J2

PXA27x FFUART serial port

J3

13 MHz SMB header

J4

JTAG ICE

J5

32 KHz SMB header

J8a

Connector to processor card

J8b

Connector to processor card

J8c

Connector to processor card

J9

Reserved

J12

RF Test Points

J13

CSSP Bottom Connector

J14

High Speed Logger (HSL) Connector

J15-J19

Logic Analyzer

J20-J21

PMIC Header

«
...
38
39
40
41
42
...
»

Содержание PXA27x Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для PXA27x Series

Бренд: Maxim Страницы: 26

Бренд: WHOOP Страницы: 26

Бренд: ZALMAN Страницы: 9

Бренд: Cytron Technologies Страницы: 13

Бренд: Galaxy Страницы: 30

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

Бренд: Kaya Instruments Страницы: 48

Бренд: CopperOptics Страницы: 12

MP5S Plus Writer

Бренд: SONIX Страницы: 23

WAFER-EHL Series

Бренд: IEI Technology Страницы: 142

Бренд: RadioSPECTRAL Страницы: 2

Бренд: ZALMAN Страницы: 9

Бренд: ActiveEye Страницы: 35

Бренд: Brickcom Страницы: 184

Бренд: Omron Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды