Intel NetStructure ZT 8101 10 Скачать руководство пользователя страница 22

Страница: 22 / 140

Intel® NetStructure™ ZT 8101 10/100 Ethernet Switch User’s Manual

Installation and Initial Setup

4. When the power on self test message appears, press the # key and wait for the following

message:

Please change your baud rate to 115200 for the Zmodem upgrade, or
press CTRL+C to go to the BOOT Menu.

If you press CTRL+C, you can configure the baud rate to a different value.

5. Change HyperTerminal’s baud rate to 115200.

6. Use the Send File function of HyperTerminal to upgrade the firmware.

When the download is completed, Zmodem will display a message indicating that it is done
and then a message about loading the Runtime image.

7. Change the baud rate of HyperTerminal back to 9600 bps.

8. Disconnect and reconnect.

9. Log in to the switch.

10. From the main menu, select Switch Information and press Enter. Verify the firmware

version.

Содержание NetStructure ZT 8101 10













































































































































Результаты поиска

Содержание NetStructure ZT 8101 10

Отзывы:

Бренды по названию

Популярные бренды

Intel NetStructure ZT 8101 10, Руководство пользователя

Результаты поиска

Содержание NetStructure ZT 8101 10

Отзывы:

Бренды по названию

Популярные бренды