manualshive.com logo in svg

Intel IXP45X, Руководство разработчика

Поделиться
Скачать
Intel IXP45X Скачать руководство пользователя страница 437

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262--, Revision: 004US

437

USB 2.0 Host Controller—Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Async Sched Not Active 

This is the initial state of the traversal state machine after a host controller reset. The 

traversal state machine will not leave this state when the Asynchronous Schedule 

Enable bit in the USBCMD register is a zero. 

This state is entered from Async Sched Active or Async Sched Sleeping states 

when the end-of-micro-frame event is detected.

Async Sched Active 

This state is entered from the Async Sched Not Active state when the periodic 

schedule is not active. It is also entered from the Async Sched Sleeping states when 

the AsyncrhonousTraversalSleepTimer expires. On every transition into this state, the 

host controller sets the Reclamation bit in the USBSTS register to a one.

While in this state, the host controller will continually traverse the asynchronous 

schedule until either the end of micro-frame or an empty list condition is detected. 

Async Sched Sleeping 

The state is entered from the Async Sched Active state when a schedule empty 

condition is detected. On entry to this state, the host controller sets the 

AsynchronousTraversalSleepTimer to AsyncSchedSleepTime. 

9.14.8.4.2

Example Derivation for AsyncSchedSleepTime 

The derivation is based on analysis of what work the host controller could be doing 

next. It assumes the host controller does not keep any state about what work is 

possibly pending in the asynchronous schedule. The schedule could contain any mix of 

the possible combinations of high- full- or low-speed control and bulk requests. 

Table 174, “Typical Low- /Full-Speed Transaction Times” on page 437

 summarizes 

some of the typical 'next transactions' that could be in the schedule, and the amount of 

time (e.g. footprint, or wall clock) the transaction will take to complete. 

Table 173.

Asynchronous Schedule State Machine Transition Actions

Action

Action Description Label

A 

On detection of the empty list, the host controller sets the 

AsynchronousTraversalSleepTimer to AsyncSchedSleepTime. 

B 

When the AsynchronousTraversalSleepTimer expires, the host controller sets the 

Reclamation bit in the USBSTS register to a one and moves the Nak Counter reload state 

machine to WaitForListHead. 

C 

The host controller cancels the sleep timer (AsynchronousTraversalSleepTimer). 

Table 174.

Typical Low- /Full-Speed Transaction Times (Sheet 1 of 2)

Transaction Attributes

Footprint

(Time)

Description

Speed

HS 

11.9 µs
9.45 µs

Maximum foot print for a worst-case, full-sized bulk data 

transaction. 
Maximum footprint for an approximate best-case, full-sized 

bulk data transaction. 

Size 512 

Type Bulk 

Speed

FS 

~50 µs

Approximate typical for full-sized bulk data. An 8-byte low-

speed is about 2x, or between 90 and 100 µs. 

Size 64 

Type Bulk 

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды