Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 20

Страница: 20 / 148

Processor Thermal/Mechanical Information

Thermal and Mechanical Design Guidelines

Section

3.1). The intercept on the thermal profile assumes a maximum ambient

operating condition that is consistent with the available chassis solutions.

To determine compliance to the thermal profile, a measurement of the actual

processor power dissipation is required. The measured power is plotted on the

Thermal Profile to determine the maximum case temperature. Using the example in
Figure

2-3 for the Intel

Core

™

2 Duo processor with 4 MB cache at Tc-max of 60.1 °C

dissipating 50 W, the maximum case temperature is 56.2 °C. See the datasheet for

the thermal profile.

Figure

2-3. Example Thermal Profile

2.2.3

CONTROL

CONTROL

defines the maximum operating temperature for the digital thermal sensor

when the thermal solution fan speed is being controlled by the digital thermal sensor.

The T

CONTROL

parameter defines a very specific processor operating region where fan

speed can be reduced. This allows the system integrator a method to reduce the

acoustic noise of the processor cooling solution, while maintaining compliance to the

processor thermal specification.

Note:

The T

CONTROL

value for the processor is relative to the Thermal Control Circuit (TCC)

activation set point which will be seen as 0 via the digital thermal sensor. As a result
the T

CONTROL

value will always be a negative number. See Chapter

4 for the

discussion the thermal management logic and features and Chapter

7 on Intel

Quiet

System Technology (Intel

QST).

The value of T

CONTROL

is driven by a number of factors. One of the most significant of

these is the processor idle power. As a result a processor with a high (closer to 0 )

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды