Intel Celeron D Скачать руководство пользователя страница 56

Страница: 56 / 64

Intel

Celeron

D Processor in the 775-Land LGA Package

Thermal Design Guide

Order #303730

Case Temperature Reference Methodology

5. Using a blade to shave excess adhesive above the IHS surface (

Figure 32

Note:

Take usual precautions when using open blades.

6. Install new Kapton* tape to hold the thermocouple wire down and fill the rest of groove with

adhesive (See

Figure 33

). Make sure the wire and insulation is entirely within the groove and

below the IHS surface.

7. Curing time for the rest of the adhesive in the groove can be reduced using Loctite*

Accelerator 7452.

8. Repeat Step 5 to remove any access adhesive to ensure flat IHS for proper mechanical contact

to the heatsink surface.

Figure 32. Removing Excess Adhesive from IHS

Figure 33. Filling the Groove with Adhesive

Kapton* Tape

Filling with

Adhesive

Содержание Celeron D

































































Результаты поиска

Содержание Celeron D

Отзывы:

Похожие инструкции для Celeron D

Бренды по названию

Популярные бренды

Intel Celeron D, Руководство по тепловому проектированию

Результаты поиска

Содержание Celeron D

Отзывы:

Похожие инструкции для Celeron D

Бренды по названию

Популярные бренды