Intel BX80605I7870 - Core i7 2.93 GHz Processor Скачать руководство пользователя страница 76

Страница: 76 / 98

Register Description

Datasheet

2.10.24 MC_CHANNEL_0_SCHEDULER_PARAMS

MC_CHANNEL_1_SCHEDULER_PARAMS

MC_CHANNEL_2_SCHEDULER_PARAMS

These are the parameters used to control parameters within the scheduler.

2.10.25 MC_CHANNEL_0_MAINTENANCE_OPS

MC_CHANNEL_1_MAINTENANCE_OPS

MC_CHANNEL_2_MAINTENANCE_OPS

This register enables various maintenance operations such as Refreshes, ZQ, RCOMP,
etc..

Device:

4, 5, 6

Function: 0

Offset:

B8h

Access as a Dword

Bit

Type

Reset

Value

Description

CS_FOR_CKE_TRANSITION.
Specifies if chip select is to be asserted when CKE transitions with PowerDown

entry/exit and SelfRefresh exit.

FLOAT_EN.
When set, the address and command lines will float to save power when

commands are not being sent out. This setting may not work with RDIMMs.

10:6

PRECASRDTHRESHOLD.
Threshold above which Medium-Low Priority reads can PRE-CAS write requests.

DISABLE_ISOC_RBC_RESERVE.
When set this bit will prevent any RBC's from being reserved for ISOC.

ENABLE2N. Enable 2n Timing.

2:0

PRIORITYCOUNTER.
Upper 3 MSB of 8 bit priority time out counter.

Device:

4, 5, 6

Function: 0

Offset:

BCh

Access as a Dword

Bit

Type

Reset

Value

Description

12:0

MAINT_CNTR.
Value to be loaded in the maintenance counter. This counter sequences the rate

to Refreshes, ZQ, RCOMP.

Содержание BX80605I7870 - Core i7 2.93 GHz Processor



































































































Результаты поиска

Содержание BX80605I7870 - Core i7 2.93 GHz Processor

Отзывы:

Похожие инструкции для BX80605I7870 - Core i7 2.93 GHz Processor

Бренды по названию

Популярные бренды

Intel BX80605I7870 - Core i7 2.93 GHz Processor, Техническое описание

Результаты поиска

Содержание BX80605I7870 - Core i7 2.93 GHz Processor

Отзывы:

Похожие инструкции для BX80605I7870 - Core i7 2.93 GHz Processor

Бренды по названию

Популярные бренды