Intel BX80570E8200 - Core 2 Duo 2.66 GHz Processor Скачать руководство пользователя страница 43

Страница: 43 / 128

Balanced Technology Extended (BTX) Thermal/Mechanical Design Information

Thermal and Mechanical Design Guidelines

5.1.3

Effective Fan Curve

The TMA must fulfill the processor cooling requirements shown in Table

5–1 when it is

installed in a functional BTX system. When installed in a system, the TMA must

operate against the backpressure created by the chassis impedance (due to vents,

bezel, peripherals, etc…) and will operate at lower net airflow than if it were tested

outside of the system on a bench top or open air environment. Therefore an allowance

must be made to accommodate or predict the reduction in Thermal Module

performance due to the reduction in heatsink airflow from chassis impedance. For this

reason, it is required that the Thermal Module satisfy the prescribed



requirements

when operating against an impedance that is characteristic for BTX platforms.

Because of the coupling between TMA thermal performance and system impedance,

the designer should understand the TMA effective fan curve. This effective fan curve

represents the performance of the fan component AND the impedance of the stator,

heatsink, duct, and flow partitioning devices. The BTX system integrator will be able to

evaluate a TMA based on the effective fan curve of the assembly and the airflow

impedance of their target system.

Note:

It is likely that at some operating points the fans speed will be driven by the system
airflow requirements and not the processor thermal limits.

Figure

5-1 shows the effective fan curve for the reference design TMA. These curves

are based on analysis. The boundary conditions used are the S2 6.9L reference

chassis, the reference TMA with the flow partitioning device, extrusion and an AVC

Type II fan geometry.

When selecting a fan for use in the TMA care should be taken that similar effective fan

curves can be achieved. Final verification requires the overlay of the Type II MASI

curve to ensure thermal compliance.

Содержание BX80570E8200 - Core 2 Duo 2.66 GHz Processor

































































































































Результаты поиска

Содержание BX80570E8200 - Core 2 Duo 2.66 GHz Processor

Отзывы:

Похожие инструкции для BX80570E8200 - Core 2 Duo 2.66 GHz Processor

Бренды по названию

Популярные бренды

Intel BX80570E8200 - Core 2 Duo 2.66 GHz Processor, Руководство по конструкции

Результаты поиска

Содержание BX80570E8200 - Core 2 Duo 2.66 GHz Processor

Отзывы:

Похожие инструкции для BX80570E8200 - Core 2 Duo 2.66 GHz Processor

Бренды по названию

Популярные бренды