Intel BOXDP55KG Скачать руководство пользователя страница 74

Страница: 74 / 92

Intel Desktop Board DP55KG Product Guide

BIOS Error Messages

When a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem. Table 16 gives an explanation of the BIOS error messages.

Table 16. BIOS Error Messages

Error Message

Explanation

PROCESSOR_THERMAL_TRIP_ERROR Processor

was previously shutdown due to a thermal

event (overheating).

CMOS_BATTERY_ERROR

The firmware has detected that a CMOS battery failure
occurred.

CMOS_CHECKSUM_ERROR

The firmware has detected that a CMOS Checksum Error

occurred.

CMOS_TIMER_ERROR

The firmware has detected that the system date/time
has not been set.

MEMORY_SIZE_DECREASE_ERROR

The firmware has detected that the system memory has

decreased.

INTRUDER_DETECTION_ERROR

The system chassis was opened.

SPD_TOLER_ERROR

SERIAL PRESENCE DETECT (SPD) device data missing or
inconclusive. Properly programmed SPD device data is

required for reliable operation.

MEM_OPTIMAL_ERROR

The installed amount of memory in Channel A is not

equal to the amount of memory in Channel B. Maximum
memory performance is achieved with equal amounts of

memory installed in each channel.

Содержание BOXDP55KG





























































































Результаты поиска

Содержание BOXDP55KG

Отзывы:

Похожие инструкции для BOXDP55KG

Бренды по названию

Популярные бренды

Intel BOXDP55KG, Руководство по эксплуатации продукта

Результаты поиска

Содержание BOXDP55KG

Отзывы:

Похожие инструкции для BOXDP55KG

Бренды по названию

Популярные бренды