manualshive.com logo in svg

Intel BLKD946GZISSL - CONROE LGA775 1066 800FSB DR2 A/V Lan SATA mATX 10Pack ACTIVE Motherboard, Технические характеристики продукции, Страница: 33 / 88

Поделиться
Скачать
Intel BLKD946GZISSL - CONROE LGA775 1066 800FSB DR2 A/V Lan SATA mATX 10Pack ACTIVE Motherboard Скачать руководство пользователя страница 33

Product Description 

 33

 

1.8

 

LAN Subsystem 

The LAN subsystem consists of the following: 

•

 

Intel 82562G Platform LAN Connect (PLC) device for 10/100 Mbits/sec Ethernet 
LAN connectivity 

•

 

Intel 82801GB ICH7 

•

 

RJ-45 LAN connector with integrated status LEDs 

Additional features of the LAN subsystem include: 

•

 

CSMA/CD protocol engine 

•

 

LAN connect interface between ICH7 and PLC device 

•

 

PCI Conventional bus power management 

⎯

 

Supports ACPI technology 

⎯

 

Supports LAN wake capabilities 

1.8.1

 

Intel

®

 82562G PLC Device 

The Intel 82562G PLC device supports the following features: 

•

 

Basic 10/100 Ethernet LAN connectivity 

•

 

Full device driver compatibility 

•

 

Programmable transit threshold 

•

 

Configuration EEPROM that contains the MAC address 

1.8.2

 

LAN Subsystem Software 

LAN software and drivers are available from Intel’s World Wide Web site. 

 

For information about  

Refer to 

Obtaining LAN software and drivers 

Section 1.2, page 15 

 

1.8.3

 

RJ-45 LAN Connector with Integrated LEDs 

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 9 below).   

Link LED

(Green)

Data Rate LED

(Yellow)

OM18388

 

Figure 9.  LAN Connector LED Locations 

Table 5 describes the LED states when the board is powered up and the LAN 
subsystem is operating. 

Содержание BLKD946GZISSL - CONROE LGA775 1066 800FSB DR2 A/V Lan SATA mATX 10Pack ACTIVE Motherboard

























































































Отзывы:

Нет отзывов