manualshive.com logo in svg

Intel BLKD945GPMLKR, Технические характеристики продукции, Страница: 23 / 94

Поделиться
Скачать
Intel BLKD945GPMLKR Скачать руководство пользователя страница 23

Product Description 

 23 

1.5.1.3  Advanced Digital Display (ADD2/ADD2+) Card Support 

The GMCH routes two multiplexed DVO ports that are each capable of driving up to a 200 MHz 
pixel clock to the PCI Express x16 connector.  The DVO ports can be paired for a dual channel 
configuration to support up to a 400 MHz pixel clock.  When an ADD2/ADD2+ card is detected, 
the Intel GMA950 graphics controller is enabled and the PCI Express x16 connector is configured 
for DVO mode.  DVO mode enables the DVO ports to be accessed by the ADD2/ADD2+ card.  An 
ADD2/ADD2+ card can either be configured to support simultaneous display with the primary 
VGA display or can be configured to support dual independent display as an extended desktop 
configuration with different color depths and resolutions.  ADD2/ADD2+ cards can be designed to 
support the following configurations: 

•

 

TV-Out (composite video) 

•

 

Transition Minimized Differential Signaling (TMDS) for DVI 1.0 

•

 

Low Voltage Differential Signaling (LVDS) 

•

 

Single device operating in dual channel mode 

•

 

VGA output 

•

 

HDTV output 

1.5.1.4 Configuration 

Modes 

A list of supported modes for the Intel GMA950 graphics controller is available as a downloadable 
document.   

 

For information about  

Refer to 

Supported video modes for the board 

Section 1.2, page 15 

1.5.2 USB 

The board supports up to eight USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and 
EHCI-compatible drivers.   

The ICH7DH provides the USB controller for all ports.  The port arrangement is as follows: 

•

 

Four ports are implemented with dual stacked back panel connectors adjacent to the audio 
connectors 

•

 

Four ports are routed to two separate front panel USB connectors 

 

NOTE 

Computer systems that have an unshielded cable attached to a USB port may not meet FCC 
Class B requirements, even if no device is attached to the cable.  Use shielded cable that meets the 
requirements for full-speed devices.  

 

For information about  

Refer to 

The location of the USB connectors on the back panel 

Figure 16, page 54 

The location of the front panel USB connectors 

Figure 17, page 56 

Содержание BLKD945GPMLKR































































































Отзывы:

Нет отзывов