manualshive.com logo in svg

Intel 82571EB EEPROM, Информационное руководство

Поделиться
Скачать
Intel 82571EB EEPROM Скачать руководство пользователя страница 24

82571EB/82572EI EEPROM Information Guide

18

Note:

The LINK/ACTIVITY source functions are slightly different from the others when BLINK is 
enabled. The LED is off if there is no LINK, on if there is LINK and no ACTIVITY, and blinks if 
there is LINK and ACTIVITY.

Note:

Asserted = active low.

NOTE:

1. The dynamic LED modes (Link/Activity and Activity) should be used with LED Blink mode enabled.

Bit

Name

Description

4

Reserved

Reserved. Set to 0b.

3:0

LED1 Mode

Initial value of the LED1_MODE field specifying what event/state/pattern 
is displayed on the LED1 (ACTIVITY) output. A value of 0011b (3h) 
indicates the ACTIVITY state. See 

Table 17

 for all available LED modes.

a.

When LED Blink mode is enabled, the appropriate LED Invert bit should be set to 0b.

Table 17.  LED Modes

Mode

Selected Mode

Source Indication

0000b

LINK_10/1000

Asserted when either 10 or 1000 Mb/s link is established and 
maintained.

0001b

LINK_100/1000

Asserted when either 100 or 1000 Mb/s link is established and 
maintained.

0010b

LINK_UP

Asserted when any speed link is established and maintained.

0011b

FILTER_ACTIVITY

Asserted when link is established and packets are being 
transmitted or received that passed MAC filtering.

0100b

LINK/ACTIVITY

Asserted when link is established AND when there is NO 
transmit or receive activity.

0101b

LINK_10

Asserted when a 10 Mb/s link is established and maintained.

0110b

LINK_100

Asserted when a 100 Mb/s link is established and maintained.

0111b

LINK_1000

Asserted when a 1000 Mb/s link is established and maintained.

1000b

SDP_MODE

LED activation is a reflection of the SDP signal. SDP0, SDP1, 
SDP2, SDP3 are reflected to LED0, LED1, LED2, LED3, 
respectively.

1001b

FULL_DUPLEX

Asserted when the link is configured for full duplex operation.

1010b

COLLISION

Asserted when a collision is observed.

1011b

ACTIVITY

Asserted when link is established and packets are being 
transmitted or received.

1100b

BUS_SIZE

Asserted when the device detects a 1 Lane PCIe* connection.

1101b

PAUSED

Asserted when the device’s transmitter is flow controlled.

1110b

LED_ON

Always asserted.

1111b

LED_OFF

Always de-asserted.

Table 16.  LED 1-3 Configuration Defaults (Word 1Ch)

Содержание 82571EB EEPROM







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды