Intel 81341 Скачать руководство пользователя страница 752 | Manualshive

Страница: 752 / 1056

background image

Intel

®

81341 and 81342—Interrupt Controller Unit

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

752

Order Number: 315037-002US

11.5.3.1 Normal Interrupt Sources

The 81341 and 81342 Interrupt Controller receives normal interrupts from the

Application DMA channels, Performance Monitoring Unit, the I

2

C Bus Interface Unit, the

ATUE, the ATUX, the Programmable Timers, the Messaging Unit and the UARTs. The

Application DMA channel interrupts for End of Transfer interrupt or End of Chain

interrupt are demultiplexed into the interrupt controller.
A valid interrupt from any of these sources outputs a level-sensitive interrupt to the

81341 and 81342 Interrupt Controller input. The corresponding IRQ or FIQ interrupt

source register bit in the interrupt controller should remain active as long as the

interrupt is pending in the peripheral unit. The appropriate interrupt source bit is

cleared by clearing the source of the interrupt at the internal peripheral.
The normal interrupt sources which drive the inputs to the 81341 and 81342 Interrupt

Controller are detailed in

.

Note:

The UART and I

2

C Bus Interface Unit interrupt sources are combined as a single

interrupt, and include both normal and error conditions within the respective units.

Table 454. Normal Interrupt Sources

Unit

Register

Interrupt Condition

Intel XScale

®

processor Overflow Flag Status Register (FLAG) Counter Overflow

ADMA Channel 2-0

ADMA Channel Status Register 2-0 End of Chain

End of Transfer

ATU -X & -E

ATU -X & -E Interrupt Status Register ATU BIST Start

Configure Reg Write

Any of the ATU Configuration registers written by an inbound

Configuration Write cycle

I

2

C Bus Interface Unit 2-

0

I

2

C Status Register 2-0

Receive Buffer Full

Transmit Buffer Empty

Slave Address Detect (General Call Address Detect)

STOP Detected

Bus Error Detected

Arbitration Lost Detected

Messaging Unit

Inbound Interrupt Status Register

Index Register Interrupt

Inbound Post Queue Interrupt

Inbound Doorbell Interrupt

Inbound Message 1 Interrupt

Inbound Message 0 Interrupt

MU MSI-X Table Write Interrupt

Selective Reset Interrupt

Coordinated Reset Interrupt

Timer 1 & 0

Timer Mode Register 1 & 0

Timer 0 has decremented to 0 interrupt.

UART Unit 1 & 0

UART 1 & 0 Interrupt ID Register

Received Line Status

Received Data is Available

Character Time-out Indications

Transmit FIFO Data Request

Autobaud Lock Indication

«
...
750
751
752
753
754
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: IBM Страницы: 86

ARM Cortex-A9 MPCore

Бренд: Dave Embedded Systems Страницы: 67

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Intel Страницы: 108

Бренд: Telex Communications Страницы: 28

Бренд: Ubiquiti Страницы: 21

Бренд: Pressalit Care Страницы: 31

Бренд: Kramer Страницы: 2

Бренд: Renesas Страницы: 746

Бренд: B&B Electronics Страницы: 17

Бренд: 2N Telekomunikace Страницы: 67

CloudGen Firewall

Бренд: Barracuda Страницы: 8

Бренд: Cypress Semiconductor Страницы: 9

Бренд: Commell Страницы: 18

Бренд: Intellinet Страницы: 32

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: SilverStone Страницы: 12

Internet Security Appliances

Бренд: SonicWALL Страницы: 293

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды