Intel 81341 Скачать руководство пользователя страница 692 | Manualshive

Страница: 692 / 1056

background image

Intel

®

81341 and 81342—SRAM Memory Controller

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

692

Order Number: 315037-002US

8.3.4

Byte Parity Checking and Generation

All the direct memory ports of the SMCU supports byte-wise parity on the data bus.
For write requests made to an SMCU port, the direct memory port interface performs

the following tasks when receiving data:

• checks for data parity on the incoming data (parity error is logged if detected)

• generates ECC on the data

For the memory ports that are connected to the south internal bus, the write data

parity is received from the south internal bus as driven by the initiator of the data on

the south internal bus. For example, south internal bus initiators generate data parity.

Since the north internal bus does not support parity, data parity is generated by the

north internal bus port as the data enters the port and before it is written to the data

queue.
For read requests made to an SMCU port, the direct memory port interface performs

the following tasks before delivering data:

• checks for ECC on the data read from memory

• generates data parity on the data before delivering it on the port

For the memory ports that are connected to the south internal bus, the read data parity

that are generated by the SMCU are directly driven onto the south internal bus to the

requester. The data parity is then verified by the requester. Since the north internal bus

does not support parity, the read data parity that are generated by the SMCU are

verified by the north internal bus port when the data is read out of the data queue and

before being delivered onto the north internal bus. If the north internal bus port detects

a parity error while reading the data out of the data queue, the north internal bus port

will return a target abort.

Figure 105. Logical Data Access Paths with Parity Protection

Direct Memory

Data_in

Data_in Parity

Data_out Parity

Data_out

Port Interface

SRAM Controller

B6360-01

«
...
690
691
692
693
694
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: Xinje Страницы: 76

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: Aurora Страницы: 6

Бренд: SriHome Страницы: 12

Бренд: 3Com Страницы: 53

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Бренд: National Instruments Страницы: 52

MULTIflight Stick

Бренд: Multiplex Страницы: 10

NC-MCO - TECHNICAL

Бренд: Crest Audio Страницы: 2

Бренд: LevelOne Страницы: 142

Fibe-Air IP-10G

Бренд: Ceragon Страницы: 71

Бренд: Enterasys Страницы: 2

Бренд: ekwb Страницы: 36

CINERGY 2400 I DT MCE edition

Бренд: TerraTec Страницы: 2

TMS320-XDS100-V3

Бренд: OLIMEX Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды