Intel 81341 Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI Express)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

250

Order Number: 315037-002US

3.3.2.1

Outbound Address Translation - Internal Bus Transactions

In addition to providing the mechanism for inbound translation, the ATU translates Intel

XScale

®

processor-initiated cycles to the PCI Express domain. This is known as

outbound address translation. Outbound transactions are processor or ADMA

transactions targeted at the PCI Express Link. The ATU internal bus target interface

claims internal bus cycles and completes the cycle on the PCI Express Link on behalf of

the Intel XScale

®

processor or DMAs.

shows 4 Gbyte memory section 0 (Internal Bus Address [35:32] = 0000

2

) of

the 81341 and 81342 memory map with all reserved address locations highlighted. The

64KByte outbound I/O window is from 0.FFFD.0000H to 0.FFFD.FFFFH while the PMMR

registers reside from 0.FFD8.0000H to 0.FFDF.FFFFH.
By default, Outbound Memory Window 0, Outbound Memory Window 1, Outbound

Memory Window 2, and Outbound Memory Window 3reside in 4 Gbyte memory

sections 1, 2, 3, and 4respectively, of the 64 Gbyte Internal Bus address space.
The response of the ATU to Outbound Transactions is globally controlled by the

Outbound Enable bit in the ATU Configuration Register as well as the Bus Master Enable

bit in each function. When the Outbound Enable bit is deasserted, outbound transaction

master-abort on the internal bus and are not forwarded to the PCI Express Domain.

When the Outbound Enable bit is asserted, the relevant Bus Master Enable bit for each

function is used to determine the appropriate response to an outbound transaction.
The Outbound ATUs behavior for the different combinations of these control bits is

described in

Table 118. Outbound Address Translation Control

Outbound Response

Outbound Enable

a

(ATUCR[1])

a. In addition, the outbound memory windows need to be individually enabled in order to claim the transaction.

When the memory widow is disabled, it does not claim a transaction which might result in a Master-Abort. By

default, Outbound Memory Windows 0 and 1 are enabled while Outbound Memory Windows 2, and 3 are

disabled.

Bus Master Enable

b

b. In a multi-function configuration, each function independently controls its own Bus Master Enable bit.

Master-Abort

0

0

Master-Abort

0

1

Retry

1

0

Claim

c

c. The ATU may respond with a Retry in this case when the Outbound Transaction Queues are full.

1

1

«
...
248
249
250
251
252
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: Lattice Semiconductor Страницы: 15

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

EXPANSION CARD X-DANTE

Бренд: Behringer Страницы: 65

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: Renesas Страницы: 76

Бренд: ZyXEL Communications Страницы: 3

Бренд: PairGain Страницы: 80

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

Бренд: V-Count Страницы: 2

DataFire GO! PRO

Бренд: Digi Страницы: 20

AdvancedTCA AT8901M

Бренд: Kontron Страницы: 76

Бренд: Freescale Semiconductor Страницы: 42

Бренд: AXIOMTEK Страницы: 2

Бренд: Z3 Technology Страницы: 94

Бренд: Renesas Страницы: 52

Бренд: Curtiss-Wright Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды