Intel 81341 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI-X)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

186

Order Number: 315037-002US

2.13.42 ATU Interrupt Status Register - ATUISR

The ATU Interrupt Status Register is used to notify the core processor of the source of

an ATU interrupt. In addition, this register is written to clear the source of the interrupt

to the interrupt unit of the 81341 and 81342. All bits in this register are Read/Clear.
Bits 4:0 are a direct reflection of bits 14:11 and bit 8 (respectively) of the ATU Status

Register (these bits are set at the same time by hardware but need to be cleared

independently). Bit 7 is set by an error associated with the internal bus of the 81341

and 81342. Bit 8 is for software BIST. The conditions that result in an ATU interrupt are

cleared by writing a 1 to the appropriate bits in this register.
Note that bits 4:0, and bits 15 and 13:7 can result in an interrupt being driven to the

Intel XScale

®

processor.

Table 65. ATU Interrupt Status Register - ATUISR (Sheet 1 of 2)

Bit

Default

Description

31:19

0000H

Reserved

18

0

2

PCI Interface Error - This bit is set when any PCI interface error occurs. When set, this bit results in the

assertion of the ATU PCI Interface Error Interrupt.

17

0

2

VPD Address Register Updated - This bit is set when a PCI bus configuration write occurs to the VPDAR

register. When set, this bit results in the assertion of the ATU Config Reg Write Interrupt.

16

0

2

Internal Bus Parity Error Detected - This bit is set when an Internal Bus Parity Error is detected.

15

0

2

ATU Configuration Write - This bit is set when a PCI bus configuration write occurs to any enabled

function. When set, this bit results in the assertion of the ATU Config Reg Write Interrupt.

14

0

2

Detected Correctable Error - This bit is set in PCI-X Mode 2 only when the 81341 and 81342 detects a

single bit ECC error in any phase of a PCI transaction.

13

0

2

Initiated Split Completion Error Message - This bit is set when the device initiates a Split Completion

Message on the PCI Bus with the Split Completion Error attribute bit set.

12

0

2

Received Split Completion Error Message - This bit is set when the device receives a Split Completion

Message from the PCI Bus with the Split Completion Error attribute bit set.

11

0

2

Power State Transition - When the Power State Field of the ATU Power Management Control/Status

Register is written to transition the ATU function Power State from D0 to D3, D0 to D1, or D3 to D0 and

the ATU Power State Transition Interrupt mask bit is cleared, this bit is set.

10

0

2

P_SERR#

Asserted - set when

P_SERR#

is asserted on the PCI bus by the ATU.

09

0

2

Detected Parity Error - set when a parity error is detected on the PCI bus even when the ATUCMD

register’s Parity Error Response bit is cleared. Set under the following conditions:

• Uncorrectable Write Data Error when the ATU is a target (inbound write).

• Uncorrectable Read Data Error when the ATU is an initiator (outbound read).

• Any Uncorrectable Address or Attribute (PCI-X Only) Error on the Bus.

08

0

2

ATU BIST Interrupt - When set, the host processor has set the start BIST, ATUBISTR register bit 6, and

the ATU BIST interrupt enable (ATUCR register bit 3) is enabled. The Intel XScale

®

processor can initiate

the software BIST and store the result in ATUBISTR register bits 3:0.

PCI

IOP

Attributes

Attributes

28

24

20

16

12

8

4

0

31

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

rv

rv

rv

rv

rc

ro

rc

ro

rc

ro

rc

ro

rc

ro

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Register Offset

+078H

«
...
184
185
186
187
188
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: SAF Страницы: 30

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Бренд: Oracle Страницы: 24

Бренд: Kanguru Страницы: 13

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: AOpen Страницы: 18

PCM-4141 Series

Бренд: Advantech Страницы: 96

Бренд: ebm-papst Страницы: 13

HHM Series HHM1521

Бренд: TDK Страницы: 2

Бренд: ekwb Страницы: 16

Threat Analysis Reporter TAR HL/SL/MSA

Бренд: 8e6 Technologies Страницы: 22

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

Бренд: Curtiss-Wright Страницы: 12

Бренд: Curtiss-Wright Страницы: 58

Бренд: MTL Страницы: 12

MEITRACK MVT380

Бренд: Shenzhen Страницы: 8

WP-N6516-M2-16P

Бренд: Wisstar Страницы: 195

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды