Intel 80331 Скачать руководство пользователя страница 63

Страница: 63 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.17

PCI 33 MHz Slot Topology

Figure 32

and

Table 24

provides routing details for a topology with for a PCI 33 MHz design with

slots.

Add-in card Impedance (microstrip and stripline)

57 Ohms +/- 15%

Stripline Trace Spacing

10 mils, from edge to edge

Microstrip Trace Spacing

15 mils, from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge-to-edge

Trace Length 1 TL1: From 80331 signal Ball to first
connector

1.0” minimum to 5.0” maximum

1.0” minimum - 4.5” maximum

Trace Length TL_EM1, TL_EM2: From 1st PCI
connector to embedded device

1.5” minimum - 4.0” maximum

Trace Length TL_AD1 from PCI connector to
receiver

0.75” minimum - 1.5” maximum

1.75” minimum - 2.75” maximum

Length Matching Requirements

No length matching is required among datalines. For length matching for
clocks, refer clock guidelines

Table 8

Number of Vias

Four vias maximum

Table 23.

PCI 66 MHz Mixed Mode Table (Sheet 2 of 2)

Parameter

Routing Guideline Lower AD Bus

Routing Guideline Upper AD Bus

Figure 32.

PCI 33 MHz Slot Routing Topology

Table 24.

PCI 33 MHz Slot Routing Recommendations (Sheet 1 of 2)

Parameter

Routing Guideline for AD Bus

Reference Plane

Route over an unbroken ground plane

Breakout

5 mils on 5 mils spacing. Maximum length of the breakout is 500 mils.

Motherboard Trace
Impedance (microstrip and
stripline)

50 Ohms +/- 15%

Add-in card Impedance
(microstrip and stripline)

57 Ohms +/- 15%

Stripline Trace Spacing

10 mils, from edge to edge

Microstrip Trace Spacing

15 mils, from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge-to-edge

Trace Length 1 TL1: From
80331 signal Ball to first
connector

1” minimum - 7.0” maximum

1” minimum - 6.5” maximum

TL1

CONN1

TL2

CONN2

L_A

AD1

AD2

TL3

CONN3

L_A

AD3

TL4

CONN4

L_A

AD4

CONN5

AD5

TL5

Содержание 80331





















































































































































Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды

Intel 80331, Руководство по конструкции

Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды