background image

Specification Update

13

Intel

®

 80219 General Purpose PCI Processor

Core Errata

Core Errata

1.

Boundary Scan Is Not Fully Compliant to the IEEE 1149.1 Specification

Problem:

The IEEE Standard 1149.1 specifies the boundary scan logic to support two main goals:

1. To allow the interconnections between the various components to be tested, test data can be 

shifted into all the boundary-scan register cells associated with component output pins and 
loaded in parallel through the component interconnections, into those cells associated with 
inputs pins; and

2. To allow the components on the board to be tested, the boundary-scan register can be used as a 

means of isolating on-chip system logic from stimuli received from surrounding components, 
while an internal self-test is performed. Alternatively, when the boundary-scan register is 
suitably designed, it can permit a limited slow-speed static test of the on-chip system logic, 
since it allows delivery of test data to the component and examination of the test results. (IEEE 
std. 1149.1-1990, page 1-5)

The Intel Xscale

®

 core does not support the second goal, because it does not support the optional 

INTEST or RUBIST instructions. The Intel Xscale

®

 core is not required to provide these 

instructions, however, since it doesn't, this makes the following statement practically invalid.

The IEEE std. 1149.1 description of the SAMPLE/PRELOAD instruction states that, “When the 
SAMPLE/PRELOAD instruction is selected, the state of all signals flowing through system pins 
(input or output) shall be loaded into the boundary scan register on the rising edge of the TCK in 
the Capture-DR controller state.” (Page 7-8).

The boundary scan cells of the Intel Xscale

®

 core bi-directional pads, do not capture the data 

driven from the on-chip system logic to the pins, when these pads are acting as outputs. This would 
only be useful when trying to capture the data driven from the on-chip logic, during normal 
operation of the assembled board. However, the Intel Xscale

®

 core does not allow single stepping 

of its clocks. Thus, even when the Intel Xscale

®

 core did provide the compliant boundary scan cell, 

it would be extremely difficult (or impossible) to synch the boundary scan logic with the state of 
the on-chip logic. Therefore, this feature of the boundary scan cells is not useful. This has NO 
effect on the ability to determine the integrity of the interconnections on boards, which is what the 
Intel Xscale

®

 core boundary scan logic was designed to support.

Workaround:

No workaround.

Status:

NoFix

.

2.

Drain Is Not Flushed Correctly when Stalled in the Pipeline

Problem:

In a load followed by a drain scenario, the load table walks and then gets a precise data abort. The 
core fetches the address for the abort handler, but in the same cycle does not flush the drain.

Implication:

Not a functional problem, but may effect performance.

Workaround:

No workaround.

Status:

NoFix

.

Содержание 80219































Отзывы: