Intel 6300ESB ICH Скачать руководство пользователя страница 252

Страница: 252 / 320

252

Intel

855GME Chipset and Intel

6300ESB ICH Embedded Platform Design Guide

Platform Clock Routing Guidelines

Table 105. Host Clock Group Routing Constraints

Parameter

Definition

Class Name

HOST_CLK

Class Type

Individual Differential Pairs

Topology

Differential Source Shunt Terminated

Reference Plane

Ground Referenced (contiguous over length)

Single Ended Trace Impedance (Zo)

±15%

Differential Mode Impedance (Zdiff)

100

±15%

Nominal Inner Layer Trace Width

4.0 mils

Nominal Inner Layer Pair Spacing (edge to edge)

(except as allowed below)

7.0 mils

Nominal Outer Layer Trace Width

5.0 mils (pin escapes only)

Nominal Outer Layer Pair Spacing (edge to edge)

(except as allowed below)

5.0 mils

Minimum Spacing to Other Signals

25 mils

Serpentine Spacing

25 mils

Maximum Via Count

5 (per side)

Series Termination Resistor Value

±5%

Shunt Termination Resistor Value

49.9

±1%

Trace Length Limits – L1 & L1’

Up to 500 mils

Trace Length Limits – L2 & L2’

Up to 200 mils

Trace Length Limits – L3 & L3’

Up to 500 mils

Trace Length Limits – L4 & L4’

2.0” to 8.0”

Total Length Range– L1 + L2 + L4

2.0” to 8.5”

Length Matching Required

Yes (Pin to Pad)

HCLK to HCLK# Length Matching

± 10 mils (per segment)

± 10 mils (overall)

CPU Clock to GMCH Clock Length Matching

Match HCLKs (pin to pad) ± 20 mils

Match L1 segment to ± 10 mils across all pairs.

Refer to

Section 11.2.1.2

for more information.

Breakout Region Exceptions

No breakout exceptions allowed.

NOTES:

1. Differential pairs should be routed as a closely coupled side-by-side pair on a single layer over their entire

length.

2. To minimize skew it is recommended that all clocks be routed on a single layer. If clock pairs are to be

routed on multiple layers, the routed length on each layer should be equalized across all clock pairs.

3. To minimize skew it is recommended that all clock pairs be length matched from CK409 pin to CPU and

GMCH die-pad, and length compensated on the motherboard for differences in package length and for
socket/interposer effective length. A table of package lengths and equivalent socket length is provided.

4. The motherboard length of the ITP connector clock pair should be matched to the motherboard length of

the CPU clock pair plus the length of the BPM#[4:0] signals, within ± 50 ps.

Содержание 6300ESB ICH

































































































































































































































































































































Результаты поиска

Содержание 6300ESB ICH

Отзывы:

Похожие инструкции для 6300ESB ICH

Бренды по названию

Популярные бренды

Intel 6300ESB ICH, Руководство по конструкции

Результаты поиска

Содержание 6300ESB ICH

Отзывы:

Похожие инструкции для 6300ESB ICH

Бренды по названию

Популярные бренды