CTCSS Tone Selection
1.
In the PROGRAM MODE press the MENU/Monitor Key (7) until the Channel Number (A) blinks on the LCD (9).
2.
Press again the MENU/Monitor Key (7) until the CTCSS Code Number (B) blinks on the LCD Display (9).
3.
Press the UP (3) or DOWN (4) keys to select the desired CTCSS Code Number. Press and hold the UP (3) or DOWN (4) keys
to move the selection quicker.
4.
Select the CTCSS Code
0
to disable the CTCSS function.
5.
To confirm and store the selection, shortly press the ON-OFF (8) key or press the MENU/Monitor (7) key to move to the next
function.
Notice :
To receive messages from other radios, transmitters and receivers (pagers) must use the same channel number and the
same CTCSS code number. Please refer to the channel and CTCSS frequency tables included in this manual.
VIBRATION Alert
This function may be operated only if the Call signal is transmitted by a transmitter/transceiver type DRS-5070 (desk type station)
or SL-02 (handheld station). If this function is enabled, when a CALL signal is received, in addition to the CALL tone the pager will
also vibrates for several seconds. This is specially useful in noisy locations, as a CALL tone alert may be missed.
1.
In the PROGRAM MODE press the MENU/Monitor Key (7) until the Channel Number (A) blinks on the LCD Display (9).
2.
Press again the MENU/MONITOR Key (7) a few times until the Vibration icon (D) blinks and the
oF
icon (A) (function disabled)
or the
on
icon (A) (function enabled) will appear on the LCD (9).
4.
Press the UP (3) or DOWN (4) keys to enable (
on
) or disable (
oF
) the Vibration Alert function.
3.
To confirm and store the selection, shortly press the ON-OFF Key (8) or press the MENU/Monitor Key (7) to keep scrolling the
other menu functions.
SPECIFICATIONS
Channels
8 PMR 446 Channels / 69 LPD 433 Channels
CTCSS Tones
38 CTCSS Codes
Operating Frequency Range
446.00625 - 446.09375 MHz (PMR Band)
433.07500 - 434.77500 MHz (LPD Band)
Power Source
2.4V (2 x AA 1,2V 1500mAh Ni-MH Rechargeable Battery)
3.0V (2 x AA 1,5V Alkaline Battery)
Audio Output
860 mV (16 ohm)
Dimensions
H85 x L60 X D36 mm
Weight
gr. 110 (battery included)
IMPORTANT INFORMATION
Important !
Changes or modifications to this product could void your authority to operate this unit. Any adjustment to your radio must be made by a qualified authorized
technician or service station. Never open the cabinet of your radio. Never change or replace anything in your radio (except batteries).
Hazardous Environments
Do not operate the radio in hazardous environments. Do not keep radio under direct rain.
Care and Safety
To clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing
permanent damage. Use a dry, lint-free cloth to clean the battery contacts. Do not submerge the unit in water or use it on a wet environment. If the unit gets
wet, turn it off and remove the battery immediately. Dry the battery and the battery compartment with a soft cloth to minimize potential water damage. Leave the
battery compartment cover off overnight to ensure complete drying. Do not use the radio until it is completely dry.
Battery Operation / Wasting
Dispose of battery in the proper manner, according to federal, state and local regulations that apply in your area. A battery may leak electrolyte if it is mixed in a
set with different battery types, if inserted incorrectly, if disposed of in fire, or if an attempt is made to charge a battery not intended to be charged. Discard leaky
batteries immediately. Leaking batteries can cause skin burns or other personal injury.
Warning !
The use of this device may be subject to national restrictions or regulations. Check your local authority or dealer before purchasing and using this product.
User Information
In accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC, 2002/96/EC and
2003/108/EC, relative to reduction of the use of hazardous substances in electrical and electronic equipment, in addition to waste disposal”. The
crossed bin symbol shown on the equipment indicates that at the end of its working life the product must be collected separately from other
waste. The user must therefore take the above equipment to the appropriate differentiated collection centres for electronic and electro technical
waste, or return it to the dealer when purchasing a new appliance of equivalent type, in a ratio of one to one. Appropriate differentiated waste
collection for subsequent recycling, treatment and environment-friendly disposal of the discarded equipment helps to prevent possible negative
environmental and health effects and encourages recycling of the component materials of the equipment. Illegal disposal of the product by the user will be
punished by application of the administrative fines provided for by the legislative decree no. 22/1997 (article 50 and following of the legislative decree no.
22/1997).
