Integra DTM-5.9, Сервисная инструкция

Страница: 34 / 79

DTM-5.9
SERVICE PROCEDURE
V e r . 1 . 0 3 / 0 8 7 0 8 A
Ex.
1. Replacing the fuses
2. Safety check out
(U.S.A. model only)
After correcting the original service problem, perform the following safety check before releasing the unit to the customer.
Leakage current Check
Measure the leakage current to a known earth ground (water pipe or conduct etc.) by connecting a leakage current
tester between the earth ground and exposed metal parts of the unit (input/output ground terminals, screw heads or metal overlays etc.).
Plug the power supply cord directly into a 120Vac 60Hz wall socket and turn ON/STANDBY button on.
Any current measured must not exceed 0.5mA.
3. Memory Backup
The receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it’s unplugged or in the
case of a power failure. Although no batteries are required, the receiver must be plugged into an AC outlet in order to charge the backup
system. Once it has been charged, the receiver will retain the settings for several weeks, although this depends on the environment and
will be shorter in humid climates.
4. To initialize the unit
1. Press and hold down VCR/DVR button, then press On / Standby button when the unit is powered on.
2. After " C l e a r " is displayed, the preset memory and each mode stored in the memory, are initialized and
will return to the factory settings.
5. To check version of Main microprocessor
1. Press and hold down
Display
button, then press
On/Standby
button when the unit is power on.
The main microprocessor version will be displayed on Front Display for about 3 seconds.
2. Press
On/Standby
button to power off.
6. Setting position before shipment
(1) Master Volume : MIN.
(2) Bass : CENTER
(3) Treble : CENTER
(4) Balance : CENTER
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse, For fuse rating, refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
REF NO. PART NAME DESCRIPTION PART NO. REMARKS
Version of Main microprocessor FW (Q701)
F901
F901 or
F903
F903 or
F911
F911 or
F912
F912 or
F913
F913 or 6A-UL/T-233
6A-T/UL-ST2
5A-UL/T-233
5A-T/UL-ST2
8A-UL/T-233
8A-T/UL-ST2
8A-UL/T-233
8A-T/UL-ST2
3.15A-UL/T-233
3.15A-T/UL-ST2 252327GR
252259GR
252326GR
252258GR
252329GR
252261GR
252329GR
252261GR
252323GR
252256GR !
!
!
!
!
!
!
!
!
! FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
www. xiaoyu163. com
QQ 376315150
9 9
2
8 9
4 2
9 8
TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com