Intec Controls MSR ELECTRONIC PolyGard AT-1110 Скачать руководство пользователя страница 9

Страница: 9 / 17

Customer Services (858) 578-7887 & (888) GO IN

TEC

Controls, 12700 Stowe Dr., Suite 1

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 141114

Polygard® is a registered trademark of MSR

AT-1110V3

PolyGard

CO Transmitter

User Manual - AT-1110 V3

Page 09



 

 
Inspection, service and calibration of the transmitters should be done by trained technicians and executed at

regularintervals.WethereforerecommendconcludingaservicecontractwithIntecWilsonMohroroneoftheir

authorizedpartners.

 
(Seesection5.1and5.2)

•

Atcommissioningandatperiodicintervalsdeterminedbythepersonresponsibleforthegasdetection

system (recommendation every 12 months).

•

Afterexchangeofthesensor

•

Ifincaseofoperationalorclimaticinfluencesthesensitivityofthesensorfallsbelow70%inoperation,

calibrationwillnotbepossibleanymore.Thenthesensorhastobechanged.

 
Considerstaticelectricity!Seepoint3.
Sensorshouldalwaysbeinstalledwithoutpowerapplied:

•

UnplugbasicPCBAT1110carefullyfromthebottompart.

•

UnplugoldsensorfromthePCB.

•

Takethenewsensoroutoftheoriginalpacking.

•

PluginthesensorelementintothePCBatX3/X7.

•

ReplugthePCBAT1110intoterminalblocksX4,X5carefully.

•

Calibrateaccordingtosection5.

Specifications subject to change without notice. | USA 141114 | Page 9 of 17

Polygard® is a registered trademark of MSR | AT-1110V3

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110_V3 – UserManual

Specifications subject to change without notice. | USA 160104 | Page 9 of 17

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110 V3 – UserManual

PolyGard

is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Содержание MSR ELECTRONIC PolyGard AT-1110


















Результаты поиска

Содержание MSR ELECTRONIC PolyGard AT-1110

Отзывы:

Бренды по названию

Популярные бренды

Intec Controls MSR ELECTRONIC PolyGard AT-1110, Руководство пользователя

Результаты поиска

Содержание MSR ELECTRONIC PolyGard AT-1110

Отзывы:

Бренды по названию

Популярные бренды