background image

ApplianceLinc Owner’s Manual  

 

Page 8 of 12 

 

X10 PROGRAMMING OPTIONS 

ApplianceLinc  is X10 ready, meaning that it can respond to X10 commands from X10 controllers. 
However,  to operate ApplianceLinc  in X10 mode, you must first set up an X10 Primary  Address. As it 
ships from the factory  or after a factory reset procedure, ApplianceLinc  will not have an  X10  Primary 
Address set up.

 

Setting the X10 Primary Address 

1)  Set ApplianceLinc to Linking Mode by pressing & holding the Set button for 3 seconds 

The ApplianceLinc Status LED will begin blinking 

 

You will have 4 minutes to complete the next step before Linking Mode automatically times out. 

2)  Using an X10 controller, send the X10 address you want to assign and the ON command 

three times

 

For example, to assign the address A1, you would send “A1 ON A1 ON A1 ON.”  

3)  Once ApplianceLinc has received the sequence, it will exit Linking Mode 

The ApplianceLinc Status LED will flash twice and then turn on solid  

Removing the X10 Primary Address 

If you are no longer going to control ApplianceLinc with an X10 Primary address, it is very important that 
you Unlink it. Otherwise, ApplianceLinc will still respond to X10 commands and may cause ApplianceLinc 
to turn on by itself.  

1)  Set ApplianceLinc to Linking Mode by pressing & holding the Set button for 3 seconds 

The ApplianceLinc Status LED will begin blinking  

2)  Set ApplianceLinc to Unlinking Mode by pressing & holding the Set button for 3 seconds  

The ApplianceLinc Status LED will continue blinking 

 

You will have 4 minutes to complete the next step before Unlinking Mode automatically times out.  

3)  Using an X10 controller, send the X10 address you wish to remove and the ON command 

three 

times

 

For example, to remove the address A1, you would send “A1 ON A1 ON A1 ON”.  

4)  Once ApplianceLinc has received the sequence, it will exit Linking Mode  

The ApplianceLinc Status LED will flash twice and then turn on solid   

 

 

 

 

 

 

 

 

Содержание ApplianceLinc 2456S













Отзывы: