background image

KNX Gateway DMX-Web K.DMXGW.01

5

Technical data

External supply
Rated voltage

AC/DC 24 V SELV (± 10%)

Mains frequency

50 / 60 Hz

Power consumption

max. 2.0 VA

Ambient conditions
Ambient temperature

-5 ... +45 °C

Storage/transport temperature

-25 ... +70 °C

Protection class

III

Fitting width

72 mm / 4 module

Weight

approx. 175 g

Network communication
IP transmission rate

10 / 100 Mbit/s

IP connection mode

RJ45 socket

KNX
KNX medium

TP

Commissioning mode

S-mode

Rated voltage KNX

DC 21 ... 32 V SELV

Connection mode KNX

Standard KNX/EIB connection terminals

Current consumption KNX

max. 5 mA

DMX
Input interface

USITT DMX512-A

Output interface

USITT DMX512-A

Connection of power supply and DMX
Connection mode

Screw terminal

single stranded

0.5 ... 4 mm²

Finely stranded without conductor sleeve

0.34 ... 4 mm²

Finely stranded with conductor sleeve

0.14 ... 2.5 mm²

6

Warranty

We reserve the right to make technical and formal changes to the product in the interest of tech-
nical progress.

We provide a warranty as provided for by law.

Please send the unit postage-free with a description of the defect to our central customer ser-
vice office:

Insta GmbH
Service Center
Hohe Steinert 10
58509 Lüdenscheid
Germany

6 / 7

82575434

06.02.2020

Содержание KNX Gateway DMX-Web K.DMXGW.01








Отзывы: