Insportline 23283 Скачать руководство пользователя | Manualshive

Страница: 22 / 27

background image

22

STEP 16

– CABLE TENSION

1. Use the weight selection pin (27) to stabilize the weight selection bar (11) and loosen the top

weight bolt (29), see. Fig. 1.

2. Remove the top part of the weights (10). Hold the pulley (9) and turn the weight selection bar

(11). If the cable is too long, turn the rod (11) clockwise. If the cable is too short, turn the rod
(11) counterclockwise, see. Fig. 2.

3. Use the pin (27) to find the most suitable tension and then tighten the bolt (29), see. Fig. 3.

4. After findin

g the most suitable cable tension, fasten the pulley (9) using a 1/2 “nut (47), see.

Fig. 4.

«
...
20
21
22
23
24
...
»

Содержание 23283




























Отзывы:

Нет отзывов

Похожие инструкции для 23283

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Baileigh Industrial Страницы: 40

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: GE Страницы: 212

Бренд: Garmin Страницы: 20

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды