4.2.20 357-05395-01 Rev A © Inovonics, 2020 - www.inovonics.com
2
1.4 EE4216MR Front Panel
Figure 2
Receiver front panel
Up Button: Scrolls the display up.
Down button: Scrolls the display down.
Back button: Returns display to the previous menu, or, when entering
information in the display, returns to the last character entered.
Enter button: Selects the currently displayed menu item. If in normal
operating mode, sets the unit to menu mode.
LCD Display: Shows status, event log and programming information.
Note:
The EE4216MR LCD will only display information when an
authorized password has been entered.
1.5 EE4216MR Internal Components
Figure 3
EE4216MR internal components
1.6 EE4216MR LEDs
Note:
The EE4216MR operation LEDs are only visible when the cover is
removed.
Output LED: Lights when any output is active.
Fault LED: Lights when any transmitter is sending a fault condition.
Power LED: Lit when receiving power.
1.7 What’s in the Carton
• Two drywall mounting anchors.
• Two wall mount screws.
• One frequency band selection jumper.
• Two pieces of mounting tape.
• Three housing screws.
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be maintained by professional
security technicians.
• Products are tested for indoor use.
• All products should be manually tested weekly.
2.2 Connect Power Cabling
Before beginning startup, you will need to connect power to the receiver. To
connect power to the receiver:
1.
Use a small screwdriver to press the housing release tab on the top of
the repeater.
2.
Connect power cabling to the Vs and GND connections.
• Power source should be 11-14 VDC. Power supply must be
unswitched, uninterrupted, and regulated.
2.3 Enable EchoStream Select
To meet ETSI requirements, Inovonics has developed a new line of EE
868MHz-only products. These new 868MHz-only products are compatible
with older systems that include EchoStream Select products. If you are
using any ES products in your current system, you will need to enable
EchoStream select compatibility on this new 868MHz-only product; if you
are not using any EchoStream select products, skip to section 2.4,
“Connect Input/Output Cabling”.
To enable EchoStream Select compatibility:
3.
Place a selection jumper on the ES selection pins.
Note:
Selection jumpers are included in the EE4216MR hardware packet.
4.
Reset the receiver or cycle power.
2.4 Connect Input/Output Cabling
5.
Connect cabling to the clear to set output.
• The optional clear to set output provides a clear to set signal to the
control panel which can be used to ensure all security devices in the
system are active before allowing the system to be set. If used by the
control panel, the system cannot be set if the receiver has not heard
from any registered wireless devices within the last 20 minutes. The
clear to set output can be set to normally open (N/O) or normally
closed (N/C) using the CTS T
YPE
command in the I
NSTALL
& S
ERVICE
menu.
6.
Connect cabling to the tamper output.
• The optional tamper output is a normally open (N/O) output that
reports receiver case tamper to an external device.
7.
Connect cabling to the jam output.
• The optional jam output is a normally closed (N/C) output that opens
for five seconds when noise thresholds on all transmission channels
remain above a predetermined value for any 20 seconds in any 60
second window. The jam output is set to the momentary output type.
8.
Connect a momentary switch to the reset input and ground.
• The optional reset input circuit permits installation of a remote
momentary normally open (N/O) switch to clear faults, unlatch
outputs, and reset the receiver to a normal state.
9.
Connect cabling to the output terminals.
Figure 4
EE4216MR Terminals
A
Up button
B
Down button
C
Back button
D
Enter button
E
LCD
display
A
Housing release tabs
B
Power connections
C
Operation LEDs
D
Output terminals
E
Tamper output
F
Clear to set output
G
Jam output
H
Reset input
I
EchoStream Select
pins
J
Housing screw tab
A
B
C
D
E
A
B
C
D
G
H
F
E
I
J
J
J
Vs
Jam output
Ground
Ta
mper output
Reset
i
n
p
u
t
Clea
r to set
ou
tp
ut
Caution:
Incorrect
connections
may cause
damage to the
unit
NC
COM
NO
NC
COM
NO
NC
COM
NO
NC
CO
M
NO
NC
CO
M
NO
NC
CO
M
NO
