Inovance Monarch MCTC-CCB-A Скачать руководство пользователя страница 13

Страница: 13 / 98

Safety Instructions

- 12 -

WARNING

◆

Require for repair services according to the product warranty agreement.

◆

When the equipment is faulty or damaged, require professionals to perform

troubleshooting and repair by following repair instructions and keep a repair record.

◆

Replace quick-wear parts of the equipment according to the replacement guide.

◆

Do not operate damaged equipment. Failure to comply may result in worse damage.

◆

After the equipment is replaced, perform wiring inspection and parameter settings again.

Disposal

WARNING

◆

Dispose of retired equipment by following local regulations or standards. Failure to

comply may result in property damage, personal injuries, or even death.

◆

Recycle retired equipment by following industry waste disposal standards to avoid

environmental pollution.

Safety Signs

For safe equipment operation and maintenance, comply with safety signs on the

equipment, and do not damage or remove the safety labels. The following table

describes the safety signs.

Safety Sign

Description

◆

Read the user guide before installation and operation.

Failure to comply will result in an electric shock.

◆

Do not remove the cover at power-on or within 10 minutes

after power-off.

◆

Before maintenance, inspection, and wiring, cut off input

and output power, and wait at least 10 minutes until the

power indicator is off.

Содержание Monarch MCTC-CCB-A



































































































Результаты поиска

Содержание Monarch MCTC-CCB-A

Отзывы:

Похожие инструкции для Monarch MCTC-CCB-A

Бренды по названию

Популярные бренды

Inovance Monarch MCTC-CCB-A, Руководство пользователя

Результаты поиска

Содержание Monarch MCTC-CCB-A

Отзывы:

Похожие инструкции для Monarch MCTC-CCB-A

Бренды по названию

Популярные бренды