background image

 Opening the Scanner  

User Manual H12 / SCAMAX® 8x1 - Version 2019.12

Page 103 of 136

6.2. 

Opening/Closing the Output Hopper(s)

Since the procedure differs between the variant with two Output Hoppers and that equipped with 
one Output Hopper, we explain the opening/closing below

...

6.2.1. 

... with One Output Hopper

The Unlocking of the Output Hopper is located on the 

right and left of the paper ejection. If a HighSpeed Sta-

cker Arm (

see chapter

 

5.7.2.

) is used, this is right in bet-

ween. To open, one of the Unlocking buttons is pushed 

up and the top part of the Output Hopper folded back-

wards. To close, the top part is guided to the front and 

engaged with light pressure from above the lock.

6.2.2. 

... with Two Output Hoppers

If the scanner is equipped with a 2nd Output Hopper, opening and closing of the 2nd Output Hopper 

is identical to the description in the previous chapter. Since the 2nd Output Hopper is placed on top 

of the Output Hopper and this is also folded up when opening the Output Hopper, the procedure for 

opening/closing the Output Hopper is different in this case.

Now the Unlocking of the Output Hopper is located in a 

grip depression that is integrated in the front left of the 

housing of the 2nd Output Hopper. To open, the Unlo-

cking latch is pulled forward and the top of the Output 

Hopper, along with the attached 2nd Output Hopper is 

opened until resistance is felt, from point this part slides 

independently to the rearmost position. To close, guide 

the open part forward again until the lock snaps in place.

Warning

Before closing the Output Hopper with an attached 2nd Output Hopper, it is essential to ensure 

that within the area of the 2nd Output Hopper, on which the Output Hopper 

(

see chapter 

1.2.2.3.

)

rests, no body parts or objects linger in order to avoid injury or damage.

Содержание SCAMAX H12









































































































































Отзывы: