manualshive.com logo in svg

INNOVATEST R130, Руководство пользователя

Поделиться
Скачать
INNOVATEST R130 Скачать руководство пользователя страница 15

www.innovatest-europe.com                                 13

9.  Probe replacement

1.  Turn the tester upside down and swivel the Probe to its 90°position.

2.   Loosen the knurled locking collar by turning it counter-clockwise approximately 3 

turns, until the access solt is aligned with the probe pin solt in the probe mounting 

block. Grasp the probe by its body section, carefully withdraw the probe from its 

mounting blockand the knurled locking collar. 

Do not grasp the probe by its 

skid and stylus end. Do not remove the knurled locking collar from 

the probe mounting block,loosen it only enough to slide the probe 

out easily

.

3.   Reverse the procedure to install a probe, aligning the pin on the bottom of the probe 

body with the acess solt in the locking collar. 

Make sure that the probe is fully 

inserted into the probe mounting block(so that the electrical connector 

is  completely  engaged)  before  tightening  the  locking  collar.  Finger 

tighten only

. 

4.  Check the tester’s calibration after changing probes.

Содержание R130





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды