Innovate LM-2 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 51

background image

Document # 31-0008

LM2_Manual_1.4.doc

10

2 Air/Fuel Ratio Setup

Innovate Motorsports’ ‘Direct Digital’ wideband measurement principal allows you to
calibrate the sensor to compensate for sensor wear. This procedure takes no more than
a couple seconds and it will insure the most accurate readings throughout the oxygen
sensor’s life.

2.1 Sensor Calibration

The calibration procedure requires that the oxygen sensor be in free air, not in the
exhaust.

1. Connect the oxygen sensor to the provided sensor cable and then to the

appropriate port on the LM-2.

Note

: The dual channel LM-2 model allows you to

connect both oxygen sensors to the unit at the same time to do the calibration
simultaneously.

2. Connect the LM-2 to the cigarette power plug with the provided cigarette power

adapter.

3. The sensor(s) will start warming up. The LM-2

will display WXX, where XX is the percentage of
temperature reached. Notice the status bar
displaying a ‘W’.

4. Next is the calibration procedure. Press and hold the

Mode

button until the

Configuration Menu appears. Select ‘Calibrate Sensors’ and press the

Enter

button.

5. Confirm by selecting ‘Start Sensor Calibration’ and press the

Enter

button.

6. The display will momentarily display ‘Cal’ and then it will switch to reading a

percentage of oxygen. If the oxygen content now differs from 20.9% by more
than 0.4%, repeat the calibration.

7. The LM-2 is calibrated and ready for use.

«
...
8
9
10
11
12
...
»

Содержание LM-2




















































Отзывы:

Нет отзывов

Похожие инструкции для LM-2

Бренд: VEE GEE Страницы: 2

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: YOKOGAWA Страницы: 16

VOLUTANK Petro 3003

Бренд: Bartec Страницы: 10

Бренд: +GF+ Страницы: 8

Бренд: Teradek Страницы: 16

Бренд: Axio MET Страницы: 5

PRO VPR100 Series

Бренд: CTC Union Страницы: 10

Бренд: PCB Piezotronics Страницы: 15

Бренд: Sercel Страницы: 63

Бренд: M & I Instruments Страницы: 3

Бренд: Kawai Страницы: 110

Panametrics XDP

Бренд: Baker Hughes Страницы: 64

Бренд: IROX Страницы: 8

Бренд: Major tech Страницы: 16

WTW pH/ION 3310

Бренд: Xylem Страницы: 48

Panel Scope VPS10

Бренд: Velleman Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды