Innovate Motorsports MTX-L Скачать руководство пользователя | Manualshive

Страница: 8 / 21

background image

MTX-L_Manual.doc

8

*Be sure to remove protective film from the gauge face. This can be done
easily with a piece of scotch tape.

4. Make sure every piece is positioned correctly using the locating tab and

reassemble the gauge.

5. Reinstall the 3 #2 phillips screws.

3 Software (LogWorks 3 and LM Programmer)

3.1 Installing software

1. Install the CD that came with your MTX-L on your Windows based personal

computer.

2. The installer will automatically start, follow the prompts to install the software.

3.

Once the software has been installed the LogWorks software, LM Programmer and
MTX-L manual can then be located by navigating through Start->Programs-
>LogWorks3.

3.2 Connecting to LM Programmer

LM Programmer is used to update firmware, change fuel types, set display ranges, and
program the two analog outputs.

1. Connect the OUT port of the MTX-L to the provided serial programming cable.

Connect the other end of the serial programming cable to your computer. If your
computer does not have a serial port, you can purchase a USB to Serial adapter

«
...
6
7
8
9
10
...
»

Содержание MTX-L






















Отзывы:

Нет отзывов

Похожие инструкции для MTX-L

Бренд: Federal Signal Corporation Страницы: 13

Бренд: KAYO MOTOR Страницы: 61

Бренд: Daikin Страницы: 6

Бренд: C&D Technologies Страницы: 5

Бренд: Garmin Страницы: 8

Бренд: Kathrein Страницы: 2

Бренд: Harbor Freight Tools Страницы: 4

Бренд: Q-See Страницы: 28

Бренд: K&M Страницы: 3

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Jumbo MultiBigShoot

Бренд: agno's Страницы: 2

Бренд: Marantz Страницы: 2

Бренд: Kolpin Outdoors Страницы: 6

Бренд: Schartec Страницы: 2

Бренд: Growatt Страницы: 10

Бренд: Ikelite Страницы: 28

Бренд: Oypla Leisure Страницы: 2

Бренд: Simplicity Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды