innovair QUANTUM Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 26

innovair QUANTUM Скачать руководство пользователя страница 11

INNOVAIR DC INVERTER QUANTUM

SERVICE MANUAL

9

Installation instructions

Location for Installing Indoor Unit

• Where there is no obstacle near the air outlet and air can be

easily blown to every corner.

• Where piping and wall hole can be easily arranged.

• Keep the required space from the unit to the ceiling and wall

according to the installation diagram on previous page.

• Where the air filter can be easily removed.

• Keep the unit and remote controller 1 m or more apart from

television, radio etc.

• keep as far as possible from fluorescent lamps.

• Do not put anything near the air inlet to obstruct it from air

absorption.

• Install on a wall that is strong enough to bear the weight of the unit.

• Install in a place that will not increase operation noise and vibration.

• Keep away from direct sunlight and heating sources. Do not place

flammable materials or combustion apparatuses on top of the unit.

Location for Installing Indoor Unit

• Where there is no obstacle near the air outlet and air can be

easily blown to every corner.

• Where piping and wall hole can be easily arranged.

• Keep the required space from the unit to the ceiling and wall

according to the installation diagram on previous page.

• Where the air filter can be easily removed.

• Keep the unit and remote controller 1 m or more apart from

television, radio etc.

• keep as far as possible from fluorescent lamps.

• Do not put anything near the air inlet to obstruct it from air

absorption.

• Install on a wall that is strong enough to bear the weight of the unit.

• Install in a place that will not increase operation noise and vibration.

• Keep away from direct sunlight and heating sources. Do not place

flammable materials or combustion apparatuses on top of the unit.

Model

Max. Allowable Tubing

Length at Shipment (m)

Limit of Tubing

Length (m)

Limit of Elevation

Difference H (m)

Required amount of

additional refrigerant (g/m)

7K-18K

5

15

5

21K-25K

5

15

5

30K

5

15

5

If the height or pipe length is out of the scope of the table, please consult the dealer.

20

30

40

«
...
9
10
11
12
13
...
»

Содержание QUANTUM



























Отзывы:

Нет отзывов