innovair ICS0629C21, Руководство по установке

Страница: 9 / 41

8
installation manual
5.4.2 Install The Panel(samll cassette type
air conditioner)
Do not coil the wiring of the swing motor into the seal
sponge.
Install the panel
Align the swing motor on the panel to the tubing joints of the
body properly.
( Refer to Fig.5-12)
Fix hooks of the panel at swing motor and its opposite sides
to the hooks of corresponding water receiver.
( Refer to
Fig.5-12.1) Then hang the other two panel hooks onto
corresponding hangers of the body. ( Refer to Fig.5-12.2)
Adjust the four panel hook screws to keep the panel
horizontal, and screw them up to the ceiling evenly.
( Refer to
Fig.5-12.3)
Regulate the panel in the direction of the arrow in Fig.5-12.4
slightly to fit the panel's center to the center of the ceiling's
opening. Guarantee that hooks of four corners are fixed well.
Keep fastening the screws under the panel hooks, until the
thickness of the sponge between the body and the panel's
outlet has been reduced to about 4~6mm. The edge of the
panel should contact with the ceiling well.
(Refer to Fig.5-13)
3
4
5
6
Fasten the rope of installation cover on the bolt of the
installation cover.
(Refer to Fig.5-16-left)
Press the installation cover into the panel slightly. (Refer to
Fig.5-16-right)
Malfunction described in Fig.5-14 can be caused by
inappropriate tightness the screw.
If the gap between the panel and ceiling still exists after
fastening the screws, the height of the indoor unit should
be modified again.
( Refer to Fig.5-15-left)
You can modify the height of the indoor unit through the
openings on the panel's four corners, if the lift of the
indoor unit and the drainpipe is not influenced
(Refer to
Fig.5-16-right).
Hang the air-in grill to the panel, then connect the lead
terminator of the swing motor and that of the control box
with corresponding terminators on the body respectively.
Relocate the air-in grill in the procedure of reversed order.
Relocate the installation cover.
CAUTION
Fig.5-27
Fig.5-28
Remove the air-in grill.
Never put the panel face down on floor or against the
wall, or on bulgy objects.
Never crash or strike it.
Slide two grill switches toward the middle at the same time,
and then pull them up.
(Refer to Fig.5-27)
Draw the grill up to an angle of about 45, and remove it.
(Refer to Fig.5-28)
1
CAUTION
Grid switch
The installation cover of the swing motor must sink into
the corresponding water receiver.
Install the panel
Align the swing motor on the panel to the tubing joints of the
body properly.
( Refer to Fig.5-29)
Hang the four fixed rope of the main body to the installation
cover and the other three covers of the swing motor:
(Refer
to Fig.5-29 and )
Install the panel on the main body with bolt (M5
×
16) and
washer. (Refer to Fig.5-29 )
Adjust the four panel hook screws to keep the panel
horizontal, and screw them up to the ceiling evenly.
Regulate the panel in the direction of the arrow in Fig.5-29.
slightly to fit the panel's center to the center of the ceiling's
opening. Guarantee that hooks of four corners are fixed well.
Keep fastening the screws under the panel hooks, until the
thickness of the sponge between the body and the panel's
outlet has been reduced to about 4~6mm. The edge of the
panel should contact with the ceiling well.
(Refer to Fig.5-30)
2
4
5
Malfunction described in Fig.5-31 can be caused by
inappropriate tightness the screw.
If the gap between the panel and ceiling still exists after
fastening the screws, the height of the indoor unit should
be modified again.
( Refer to Fig.5-32-left)
You can modify the height of the indoor unit through the
openings on the panel's four cor ners, if the lift of the
indoor unit and the drainpipe is not influenced
(Refer to
Fig.5-32-right).
Hang the air-in grill to the panel, then connect the lead
terminator of the swing motor and that of the control box
with corresponding terminators on the body respectively.
Relocate the air-in grid in the procedure of reversed order,
install the air-in grid.
CAUTION