background image

 

Innova S.r.l.

 

Page  21 

HRP DOMO EXT Manual 

 

 
 

5.3

 

SWITCHING THE UNIT ON AND OFF   

 

-The unit can be enabled and disabled using the On / Off button on the display. 
 
   

 

Switching the unit on / off 

 

5.4

 

MODIFYING FAN SPEEDS AND BOOSTER FUNCTION 

 

-The display shows the button to select the desired speed of the unit; 
Each time the speed is selected, the actual fan speed changes after 1 second. 
 
-There are three selectable speeds: 
Night (low speed) – nominal (medium speed) – high (high speed) 

 

Fan speed management 

 

5.5

 

NOMINAL SPEED OPERATION 

 

-Pressing the auto button will operate the unit at the nominal speed while keeping the sensor input 

control active; 
  The humidity regulator or air quality regulator will increase the speed of the unit if required 

corresponding to 
  the sensor speed; The input is digital to which a potential-free contact can be connected; 

 

AUTO operation 

 

5.6

 

CHANGING THE SEASON 

 

-Season modification on version I must be effected using the keypad; 
  Press and hold the season change button for at least 3 seconds to change season status; 
  This operation must be carried out to activate the correct logic: 
  Frost protection in winter and bypass in summer; 
  Symbol logic: SUN – WINTER             SNOWFLAKE (SUMMER) 

 

Season Change 

 
 

Содержание HRP DOMO EXT





























Отзывы: