OPERATION GUIDE:
The Disrupter has three buttons:
“ ” button, “ ” button and “ ” button.
“ ” button: Power
“ ” button: Disrupter / VW
“ ” button: Disrupter / VW
To POWER ON the Disrupter :
Pressing the power button “ ” three
times in rapid succession will power on
the Disrupter Advanced Personal
Vaporizer. The main LED light will blink
from red to yellow to green after which
the Disrupter Advanced Personal
Vaporizer will enter standby mode. The
final color of the LED will indicate the
current power level.
ON/OFF Battery Switch :
Press the power button“ ”three times
to turn the Disrupter on. Once the
Disrupter is on, hold down the power
button to vape. When the Disrupter is
not in use, press the power button “ ”
three times in succession to power off
the Disrupter.
Always power off the Disrupter when it
is not being used, or when it is going to
be stored in a pocket, bag or purse.
FLIP OLED SCREEN ORIENTATION:
Hold “ ” and “ ” button for 3 seconds
to flip the horizontal orientation of the
screen.
SAFETY :
15 second cutoff:
If the “ ” button is held for 15 seconds
or longer the Disrupter Advanced
Personal Vaporizer LED lights will flash
and than stop firing until the “ ” button
is released and pressed again.
0.50Ω
0.00W
V
1.50Ω
0.00V
40.0W Low Resistance
0.00Ω
0.00V
40.0W
SHORTED
-.-
-Ω
0.00W
4.00V
0.50Ω
4.20V
100
Low Voltage Warning:
The Red LED and Battery bar will blink
when the battery capacity is lower than
3.3V and the Disrupter will power off
automatically .
Short Circuit/Atomizer Protection:
Short Circuit/Atomizer Protection protects
the Disrupter Advanced Personal Vaporizer
against shorted atomizers and will stop the
unit from functioning in unsafe conditions.
The Disrupter features automatic real-time
atomizer Ohms detection. If the resistance
of the atomizer is lower than 0.2 Ohm the
Disrupter OLED screen will not power on
and it will display:
Over-Discharge Protection:
The InnokinCell Vaping Power System
monitors the battery voltage and will
automatically power off if the battery is
over discharged.
‘Vape while charging’ Technology:
The InnokinCell is recharged with a
Micro USB cable. When plugged into a
power source the Disrupter can also be
vaped and charged at the same time
with Innokin Technology’s ‘Vape while
you charge’ pass-through technology.
Remembers last Voltage or Wattage setting:
When the Disrupter is turned off by the
power button it will remember the
current voltage or wattage setting and it
will retain the setting when the
Disrupter is powered back on.
When the Disrupter Advanced Personal
Vaporizer has been powered on Hold
the “ ” button down to activate the
vaporier. The color of the LED when the
button is pressed indicates the current
power level.
When the button “ ” is pressed (with a
clearomizer attached) the OLED screen
will display the attached atomizer
resistance, voltage and wattage and
remaining battery charge.
When the button “ ” is continuously
pressed (with a clearomizer attached) ,
the OLED screen will display:
To POWER OFF the Disrupter:
Ohms Meter & Battery Level Indicator
& Puff Counter:
With an atomizer attached, hold both
the “ ” and “ ”buttons simultaneously
and the OLED screen will display the
resistance of the attached atomizer, the
battery voltage, the number of puffs
since the device was last turned off and
the last set voltage or wattage.
Enter Variable Wattage Mode:
Press and hold the “ ” and “ ” buttons
for 1 second to enter variable wattage
mode.
Adjust Variable Wattage:
When the Disrupter is in variable
wattage mode press the “ ” or “ ”
button to unlock the wattage. Hold the
button down to quickly increase or
decrease the set wattage. Press the “ ”
to lock to wattage and vape.
The Disrupter wattage can be adjusted
from 6.0 to 50 watts in .5 watt
increments by pressing the “ ” or “ ”
buttons. If the wattage is decreased
below 6 Watts it will cycle up to 50
Watts. If the wattage is increased from
50 Watts it will cycle down to 6 watts.
Press the button “ ” to lock the set
wattage and fire the Disrupter.
Enter Variable Voltage Mode:
Press and hold the “ ” button and then
the “ ” button for 1 second to enter
variable voltage mode.
In variable voltage mode the Disrupter
voltage can be adjusted from 3.0 to 7.5
volts in .1 volt increments by pressing
the “ ” or “ ” buttons.
Adjust Variable Voltage:
When the Disrupter is in variable
voltage mode press the “ ” or “ ”
button one time and then press it again
to unlockthe voltage. Hold the “ ” or
“ ” button down to quickly increase or
decrease the set voltage.
The Disrupter voltage can be adjusted
from 3.0 to 7.5 volts in .1 volts. If the
voltage is decreased below 3 volts it will
cycle up to 7.5 Volts. If the voltage is
increased from 7.5 Volts it will cycle
down to 3 volts. Press the button “ ”
to lock the set voltage and fire the
Disrupter.
Check Atomizer:
When the atomizer is not connecting
properly, or resistance more than 9.9
Ohm, the screen will display “CHECK
ATOMIZER” when press the firing
button .
The Disrupter features automatic real-time
battery voltage detection.
Overheat Protection:
The Disrupter features automatic real-time
PCB Chipset temperature detection.
The screen will display “ TOO HOT ” if the
PCB is overheated.
Important: Explaining Low-Resistance /
High Wattage Vaping
To ensure you have the best possible
vaping experience it is important to have a
basic understanding of wattage, voltage
and coil resistance. There is a range of
standard coil resistances: 2.1, 1.7, 1.4, 1.1,
0.8, 0.5 ohm etc and Rebuildable
Atomizers or Drippers (RBA/RDA) may
even be lower. The Disrupter can fire
between resistances of 3.1 to .2 ohm and
you can clearly see the resistance of the
attached clearomizer on the OLED screen.
0.50Ω
0.00V
40.0W
0.50Ω
0.00V
15.0W
0.50Ω
4.47V
10.0S
0.50Ω
32.0W
1.0S
0.50Ω
4.20V
100
0.50Ω
0.00V
40.0W
0.50Ω
0.00W
4.00V
We would suggest that for coil
resistances of 1.7 – 2.1 ohm you can
begin with a setting of 8 Watts and then
increase the Wattage until you find your
perfect setting. For resistances of 0.5,
you can try a setting of 25 Watts and
increase the wattage until you find your
perfect vaping setting.
We would suggest that for coil
resistances of 1.7 – 2.1 ohm you can
begin with a setting of 4.0 Volts and
then increase the Voltage until you find
your perfect setting. For resistances of
0.5, you can try a setting of 3.3 Volts and
increase the voltage until you find your
perfect vaping setting.
If you have any questions please contact
your local Authorized Innokin Vendor.
Important:
The Disrupter will only fire
variable voltage or variable wattage
depending on the last setting chosen; it
will not fire both. You must choose
either Variable Voltage or Variable
Wattage.
The main LED will display green to
indicate a full battery charge, yellow
indicates power is at half capacity and
red indicates immediate charging is
required.
Red
LED light = battery voltage is lower
than 3.6V
Yellow
LED light = battery voltage is
around 3.6V-3.74V
Green
LED light = battery voltage is
higher than 3.75V
PLEASE NOTE:
The Red LED will blink for eight seconds
when battery capacity is lower than 3.3V
and the Disrupter will automatically power
off.
Technical Specifications:
Operating Voltage: 3.0V-7.5V
Operating Wattage: 6.0W-50W
Battery : 2000mAh
Standby current: 100uA max
Maximum output Wattage: 50W
Maximum output Current: 16A
Maximum Working Current
20Amp Max Continuous Output
Maximum output Voltage: 7.5V
Clearomizer Resistance: 0.2Ohm (minimum)
Charging: Micro USB DC5V/1A
WARRANTY INFORMATION:
Innokin Technology provides a 90 day after
sales service warranty to all of our authorized
vendors.
Please consult the official Innokin website or
your Authorized Innokin Technology Vendor
for more information and terms of service.
Keep the proof of purchase of this device.
The proof of purchase is needed for the 90
Day Limited Warranty.
For more information and to download the
warranty card please visit:
http://www.innokin.com/index.php/en/
about-us-en/innokin-90-day-limited
-warranty-program
