inTC Series
Teller Camera
Quick Start Guide
Before operating this product, please read this quick-start guide to ensure proper use.
Please store these instructions a safe place for future reference.
FEATURES
•
Compact Design
•
High Sensitivity sensor
•
800TVL Resolution
•
0.01 Lux
•
Wide Dynamic Range
•
HLC, BLC, DEFOG
•
Dual Optical Vari-Focal
•
Sens Up
•
Optional UTC Programmer
•
12VDC or 24VAC
PRECAUTIONS
1. Before installing and operating the unit, please read this manual carefully.
2. Precision components are contained in this camera, please avoid violent vibrations during
installation and maintenance. Do not connect the power until you have completed the
installation.
3. Please obey all local electrical wiring regulations when using this unit.
4. Do not use abrasive or corrosive materials for cleaning. Use only a soft cloth for cleaning.
5. To prevent damage to the lens or sensor, do not point the camera directly into the sun
or very strong light sources.
6. Do not use the camera outside it’s working temperature (-10°C~ 50°C / 14°F ~122°F) or
humidity (<90%) ranges.
7. Ensure that the power supply meets the current requirements of the camera and that
the supply voltage is inside the tolerances of the camera: 24VAC ±10%
8. Ensure that the fixings used are adequate to support the load of camera.
9. In case of camera failure, do not attempt to dismantle or service the camera yourself.
Please refer to qualified service personnel for repair of the camera.
CONNECTIONS
Connections for video and power are made to the flying lead from at the rear of
the camera. Two connectors are provided:
1. Video output connector, 75Ω BNC socket. Connect a male BNC connector to a
Monitor, DVR or UTC programmer to this socket.
2. Power Input connector. This is a 2.1mm DC jack. Connect 24VAC or 12VDC.
Observe polarity of 12VDC connections. The centre conductor is +12VDC ±10%
and outer is ground. Refer to the adjacent diagram for clarification.
OSD ACCESS
The camera is supplied in a general configuration that will suit the majority of
installation requirements. Should advanced configuration be required, the optional
UTC (up the coax) Programmer may be connected to the camera to access the
camera On Screen Display (OSD) for user programming.
MENU
Exposure..
Day/Night..
WhiteBalance..
Display Adjust..
Connect the Video-In connector of the UTC controller to the Video-Out connector
of the camera. Connect the Video-Out of the UTC controller to a display monitor. To
activate the camera OSD, depress the joystick button on the UTC Controller (operation
is confirmed when LED is latched on).
Push the joystick
to select a menu from the list.
Push the joystick
to change the selected value.
Press the joystick button to call the sub-menu or execute a command.
To return from a sub-menu to the previous menu, select “Return” and press the
joystick button.
OSD MAIN MENU
When the OSD menu is launched, you are presented with the adjacent opening screen.
A menu option followed by a
indicates the presence of a sub-menu. Options set to
OFF will not show a
until set to ON
Use RETURN
to return to the previous menu.
LENS menu:
• MODE
- DC or manual selection
Indoor -
Default, set to fixed values
OUTDOOR
-
Iris and shutter will auto adjust to lighting situation.
• LENS
- Used to optimize iris level using damping load.
EXPOSURE menu:
• SHUTTER
- Auto, Manual, FLK selection, 1/60~1/50K. (1/50~50K PAL) Set
this on to reduce the exposure time of each image. This can be used to
reduce blur in images with fast changing content. FLK mode; Use this
when flicker is observed in the image under fluorescent lighting. When
WDR is ON, the shutter menu is disabled.
• AGC- Off or Level Control -
Used to adjust overall gain.
• SENS UP -
Slows frame rate and increases low light sensitivity.
• BRIGHTNESS -
Sets the level of the overall brightness
• D-WDR -
Actively controls gamma compensation to provide optimal
image exposure in images with
extremes of lighting. When WDR is ON
the D-WDR menu is disabled.
• DEFOG-
Improves the clarity of
image obscured by fog by analysing
the brightness of the image and
compensates the color of the image.
• BACKLIGHT - BLC or HLC
Adjust the
area to be enhanced and sets the level
for
BLC
.
HLC
is the ability to reverse bright points to black or gray, (areas
such as headlights, any high luminance areas) this function will improve
the overall picture. When WDR is ON the backlight menu is disabled.
WDR
WDR
- On,Off
• GAIN
- Low, Middle, High - Sets level of WDR .
• WDR OFFSET
- Used to improve contrast in bright/dark areas.
Rev 0.1
MAIN MENU
LENS
DC
EXPOSURE.
WDR
OFF
WHITE BAL
ATW
DAY&NIGHT
AUTO
NR
SPECIAL
ADJUST
VIDEO OUT
NORMAL
RESET
EXIT
SAVE
EXPOSURE
SHUTTER
AUTO
AGC
ON
SENS-UP
AUTO
BRIGHTNESS 40
D-WDR
OFF
DEFOG
OFF
BACKLIGHT
OFF
RETURN
RET
LENS
LENS
MODE
INDOOR
LENS
ADJUST
RETURN
RET
EXPOSURE MENU
WDR
GAIN
MIDDLE
WDR OFFSET
RETURN
RET
12VDC
GND
