background image

IN3218HR OPERATION MANUAL  -  REV. 1.0  01/04/01                       

 ©2000  -  INLINE, INC. 

 

Warranty 

 
 
     

  INLINE warrants the equipment it manufactures to be free from defects in materials and 

 workmanship. 
 
     

 

If equipment fails because of such defects and INLINE is notified within two (2) years from the 
date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided 
that the equipment has not been subjected to mechanical, electrical, or other abuse or 
modifications. 

 
     

 

Equipment that fails under conditions other than those covered will be repaired at the current 
price of parts and labor in effect at the time of repair.  Such repairs are warranted for ninety (90) 
days from the day of re-shipment to the Buyer. 

 
     

 

This warranty is in lieu of all other warranties expressed or implied, including without 
limitation, any implied warranty or merchantibility or fitness for any particular purpose, 
all of which are expressly disclaimed. 

 
 
 
 
 
 
 
 

The information in this manual has been carefully checked and is believed to be accurate.  However, 
INLINE, Inc. assumes no responsibility for any inaccuracies that may be contained in this manual.  In no event 
will INLINE, Inc. be liable for direct, indirect, special, incidental, or consequential damages resulting from 
any defect or omission in this manual, even if advised of the possibility of such damages.  The technical 
information contained herein regarding IN3218HR features and specifications is subject to change without 
notice. 

 

 
 
 
 
 
 
 

                                All trademarks and brands are property of their respective companies. 
                                                       All Rights Reserved   © Copyright 2000 

 

  

©

 INLINE, INC.  

  22860 SAVI RANCH PARKWAY  

  YORBA LINDA, CA  92887 

 (800) 882-7117    

     (714) 921-4100    

    FAX  (714) 921-4160    

    www.inlineinc.com 

Содержание IN3218HR









Отзывы: