background image

MIXING AMPLIFIER

IPA-60/120/240/36   

7

1. MIC INPUT JACK (MIC1~MIC4)

These jacks are used when you want to use MIC 1~4

inputs and it is consisted with electronic balanced for

noise prevention.

2. MIC 1 MUTE CONTROL

By incoming signal on MIC1, this controller blocks all

signals except MIC 1 and CHIME by priority order.

3. AUX 1 ~ 3 INPUT JACK

Connect an external source(CD,TUNER,DECK etc) to

these input.

4. AMP INPUT JACK

By connecting external device

s signal to this input

jack, it can be used to expand amplifiers. Also, it can be

used as patch by connecting effectors between pre-

amplifier output and amplifier input of this device.

5. PRE-AMP OUTPUT JACK

This output provides line level output signal for

connection to an external amplifier.

6. PHANTOM POWER SWITCH

When you want to use condenser MIC, if turn on this

switch, +15V condenser MIC power is supplied on No.2

and 3 of XLR jack. Because this power is supplied to

microphones in parallel, you can connect it to other

dynamic microphones. However, if connect it to other

types of MIC, be sure about plug wiring to do not

unbalanced.

*

Note

: If turn on this switch when volume controller of

input channel and mater volume controller is not

placed at minimized, impact voltage can be incurred

suddenly to MIC circuit, and it may cause defeats of

speaker.

7. EXTERNAL CHIME SWITCH

Connect the switch to this terminal if you want to use 4-

tone chime remotely.

8. MONITOR ATT. SWITCH

It controls the volume of monitor speaker.

9. SPEAKER OUTPUT

This terminal is used to connect speaker, be careful to

do not overload.

Impedance and output voltage are as follows. Be

noticed that SP 1~5 terminals are controlled by speaker

select-switch on the front panel.

IPA-60

4

Ω

/15.5V

8

Ω

/17.8V

166

Ω

/100V

IPA-120

4

Ω

/21.9V

8

Ω

/30.9V

83.3

Ω

/100V

IPA-240

4

Ω

/30.9V

8

Ω

/43.8V

41.6

Ω

/100V

IPA-360

4

Ω

/37.9V

8

Ω

/53.6V

27.7

Ω

/100V

10. AC CONNECTOR AND FUSE HOLDER

Connect the supplied standard AC input cable to this

input. The fuse holder below the input contains the AC

overload protection fuse.

If the fuse has blown out, replace it with a fuse of the

same type and rating. If the fuse continues to blow,

refer servicing to a qualified service technician.

11.ANTENNA TERMINAL (when set IPA-CDR/U)

When set our model, IPA-CDR/U (1CD&MP3,TUNER,

USB) on this device,this terminal connects antenna.

Rear Panel

Содержание IPA-120

















Отзывы: