background image

Instruction Manual

P/N:SES3082ICP

Page 2 SES3082ICP

The SuperNano-Web filter media is a dry synthetic media that outperforms the competition. The media itself is a proprietary base blend of synthetics and

cellulose. Cellulose fibers are larger than synthetic fibers, and have larger spaces between the fibers, causing contaminants to load in the depth of the
media and plug the airflow path. This creates higher restriction levels and less capacity. The synthetic fibers in the SuperNano-Web media are submicron
in diameter and have small interior fiber spaces, which result in more contaminants being captured on the surface of the media. This can help keep restric-
tion levels low as the filter loads with dirt and containments

To Clean your filter:

Carefully remove the filter from the housing. Once removed, wipe down the housing using a clean shop towel, being careful not to knock any dirt and/or
debris in the air inlet. Your filters can be cleaned by carefully vacuuming the filter media from the dirty side, or by holding the filter with one hand and care-
fully blowing the filter media at a 45-degree angle from the clean side using low-pressure shop air (15-20 lbs. psi).

*IT I

S IMPORTANT TO NOT USE ANY CLEANERS ON THE SUPERNANO-WEB MEDIA OR APPLY ANY OIL!!!

NOTE: 

This intake kit may not work on vehicles

with the following aftermarket modifications.

•Aftermarket Intercooler piping

•Aftermarket intercooler

•Turbo upgrade

•Modified body panels

•Suspension & Chassis modifications

If you look at the picture to the left, you can see the Nano-

fiber web on top of our base media. That web, or Super-
Nano-Web as we like to call it, helps trap smaller particles
and protect your engine.

Injen intake systems are street legal in most states unless the state is adopting to

California Emissions standards. States that have adopted California emission stan-
dards include: Arizona, California, Connecticut, District of Columbia, Maine, Mary-
land, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania,
Rhode Island, Vermont, and Washington. These states will require an California Air
Resource Board Executive Order Number (CARB E.O.) for the legal use of an
Injen intake system in your vehicle for use on public roads or highways. These ve-
hicle will be considered "Legal in California only for racing vehicles competition use
only, which may never be used upon a public street or highway. 

Please keep your

factory air box assembly for any future use.

NOTE: DISCONNECT BATTERY BEFORE INSTALLATION!!!

Содержание SES3082ICP






Отзывы: