background image

 

EQ50 Owner’s Manual 

 

 

12/2016 

 

 

 

21

 

 

replacement of any product.  Products returned to Ingram Engineering that do not meet the 
terms of this Warranty will be repaired and returned C.O. D. with billing for labor, materials, 
return freight, and insurance.  Products repaired under warranty at the factory will be returned 
freight prepaid by Ingram Engineering to any location within the boundaries of the USA. 
 
Ingram Engineering warrants all repairs performed for 90 days or for the remainder of the 
warranty period.  This warranty does not extend to damage resulting from improper installation, 
misuse, neglect or abuse, or to exterior appearance.  This warranty is recognized only if the 
inspection seals and serial number on the unit have not been defaced or removed.  
 
Ingram Engineering assumes no responsibility for the quality or timeliness of repairs performed 
by Authorized Ingram Engineering Service Centers. 
 
This warranty is extended to the original purchaser and to anyone who may subsequently 
purchase this product within the applicable warranty period.  A copy of the original sales 
receipt is required to obtain warranty repairs.  
  
This is your sole warranty.  Ingram Engineering does not authorize any third party including 
any dealer or sales representative, to assume any liability on behalf of Ingram Engineering or 
to make any warranty for Ingram Engineering.  
 

THIS WARRANTY GIVEN ON THESE PAGES IS THE SOLE WARRANTY GIVEN BY 
INGRAM ENGINEERING AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS AND 
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE.  THE WARRANTY GIVEN ON THESE PAGES SHALL BE 
STRICTLY LIMITED IN DURATION TO THREE YEARS FROM THE DATE OF ORIGINAL 
PURCHASE FROM AN AUTHORIZED INGRAM ENGINEERING DEALER.   UPON 
EXPIRATION OF THE APPLICABLE WARRANTY PERIOD, INGRAM ENGINEERING 
SHALL HAVE NO FURTHER WARRANTY OBLIGATION OF ANY KIND.  INGRAM 
ENGINEERING SHALL NOT BE LIABLE FOR ANY INCIDENTAL, SPECIAL, OR 
CONSEQUENTIAL DAMAGES THAT MAY RESULT FROM ANY DEFECT IN THE INGRAM 
ENGINEERING PRODUCT OR ANY WARRANTY CLAIM.

  Some states do not allow 

exclusion or limitation of incidental, special or consequential damages or a limitation on how 
long warranties last, so some of the above limitations and exclusions may not apply to you.  
This warranty provides specific legal rights and you may have other rights which vary from 
state to state.     
 
 
 

Содержание EQ50
























Отзывы: