background image

 

INGECON SUN STORAGE 1Play

 

Technical Guide 

30/09/2019 

7/9

 

5  Setting the inverter 

This chapter describes how to configure the inverter settings when the ISS 1Play has been wired to the 
Pylontech battery. 

To do so, once all the previous steps have been completed, the following steps must be followed: 

5.1  DC Battery type 

Please be careful to choose the right battery type when you set up the configuration in 
your inverter. The battery or inverter manufacturers have no responsibility on the 
damages caused due to incorrect configurations. For instance, if you select “Lead-acid” 
as a battery type in the inverter configuration and the battery being used is “Lithium-ion”, 
the battery might get damaged or experience performance degradation. 

 

It is required to set the DC Battery type: 

Pylontech Force H1/H2 or Powercube X1/X2 

This can be done using the “Ingecon Sun Manager” software package (downloadable on 

www.ingeteam.com

or through the display: 

Using Ingecon Sun Manager: 

Settings 

 1-.DC BATTERY TYPE: Type of Battery > Lithium: Pylontech Force H1/H2 

 

or 

Settings 

 1-.DC BATTERY TYPE: Type of Battery > Lithium: Pylontech Powercube X1/X2 

 

Figure 1: DC Battery selection on Ingecon Sun Manager. 

Click on the “Send” button.  A screen informing that the configuration was successfully saved must appear 
when the settings are correctly applied to the inverter. 

Using the Display: 

To perform any configuration change through the display, the required installer password must be entered on: 

MAIN MENU > CONFIGURATION > ENTER PASSWORD 

The password is indicated on the “Installation and Operation Manual”, on the chapter dedicated to 
configuration. 

When the permission is given, go to: 

MAIN MENU > CONFIGURATION > BATTERY > LITHIUM > PYLONTECH HV > FORCE H1/H2  

or 

MAIN MENU > CONFIGURATION > BATTERY > LITHIUM > PYLONTECH HV > POWERCUBE X1/X2 

Confirm the desired selection by pressing the “OK” button.  A message to confirm the modification will pop up. 
A final screen that shows that the process has been completed will be shown on the display. 

 

Francisco Javier F.J.A. Ancn Jimenez

2019.10.31 08:36:45

Firmante: 

CN=Francisco Javier F.J.A. Ancn [email protected]=com0.9.2342.19200300.100.1.25=ingeteamrenovables

Llave publica: 

RSA/2048 bits

Содержание INGECON SUN STORAGE 1Play 3TL










Отзывы: