Ingersoll-Rand VHP750WCAT Скачать руководство пользователя

Страница: 80 / 89

Operating & Maintenance Manual

Fault Finding

Book: 22846471 (3-09-07) Rev. B

Air discharge
capacity too low.

Engine speed too low.

Check the air cylinder and air filter(s).

Blocked air cleaner.

Check the restriction indicators and replace
the element(s) if necessary.

High pressure air
escaping.

Check for leaks.

Incorrectly set regulation
system.

Reset the regulation system. Refer to

SPEED AND PRESSURE REGULATION
ADJUSTMENT

in the

MAINTENANCE

section of this manual.

Compressor
overheats.

Low oil level.

Top up the oil level and check for leaks.

Dirty or blocked oil
cooler.

Clean the oil cooler fins.

Incorrect grade of oil.

Use Ingersoll-Rand recommended oil.

Defective by-pass valve.

Check the operation of the element and
replace if necessary.

Recirculation of cooling
air.

Move the machine to avoid recirculation.

Reduced cooling air
from fan.

Check the fan and the drive belts. Check for
any obstruction inside the fan cowl.

Excessive oil
present in the
discharge air.

Blocked scavenge line.

Check the scavenge line, drop tube and
orifice. Clean and replace.

Perforated separator
element.

Replace the separator element.

Pressure in the system
is too low.

Check the minimum pressure valve.

FAULT

CAUSE

REMEDY

Содержание VHP750WCAT


























































































Результаты поиска

Содержание VHP750WCAT

Отзывы:

Похожие инструкции для VHP750WCAT

Бренды по названию

Популярные бренды

Ingersoll-Rand VHP750WCAT, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание VHP750WCAT

Отзывы:

Похожие инструкции для VHP750WCAT

Бренды по названию

Популярные бренды