Ingersoll-Rand NVC 200 Скачать руководство пользователя страница 15

Страница: 15 / 23

ingersollrandproducts.com

PROBLEM

SYMPTOM(S)

POSSIBLE CaUSE

CORRECTIVE aCTION

Apparent controller

display malfunction

Display Blank

Blown Fuse

Check Fuses

Board Failure

Contact your local distributor

for further assistance.

Unrealistic temperature

displayed

Probe loose, off connection or

defective probe

Inspect probe cable and

terminal connection Replace

probe

Erratic or inaccurate

temperature readings

Probe not completely in

thermal well

Inspect probe and check

readings against independent

source (eg. temperature

analyzer/pyrometer/ice bath)

both in temperature well and to

ambient

Defective probe

Replace probe

Unrealistic pressure

displayed

Transducer loose, off

connection or defective

transducer

Inspect transducer cable and

terminal connection
Replace transducer

High pressure drop

across dryer

Outlet pressure

substantially lower than

inlet pressure System

operating temperature is

above 32°F

Inlet and outlet valves not

completely open

Open valves

Inlet and outlet filters blocked

up.

Change filter elements

Outlet pressure

substantially lower than

inlet pressure System

operating temperature is

below 32°F

Compressor relay / contactor

stuck.

Replace relay / contactor.

Microprocessor Control relay

bad

Replace relay

Probe not completely in

thermal well

Inspect probe and check

readings against independent

source (eg. temperature

analyzer/pyrometer/ice bath)

both in exchanger well and to

ambient

Problem persists

Turn dryer off and consult your

local distributor for further

assistance

Condensate drain

does not fire

Check installation is in

accordance with this manual.

Revise installation accordingly.

Inlet / outlet pipe internal

diameter too small causing

air-lock or back pressure.

Replace with larger diameter

piping.

Excessive use of bends / elbows

in inlet / outlet pipe work

causing air-lock/ back pressure.

Reduce the amount of bends

and elbows.

Outlet pipe too long / too

high causing back pressure.

Reconfigure condensate piping.

More than one condensate

source connected providing

alternative path for

condensate.

Reroute condensate to

eliminate secondary

path. Install check valves as

required.

10.0 TROUBLESHOOTINg

Содержание NVC 200
























Результаты поиска

Содержание NVC 200

Отзывы:

Похожие инструкции для NVC 200

Бренды по названию

Популярные бренды

Ingersoll-Rand NVC 200, Руководство оператора

Результаты поиска

Содержание NVC 200

Отзывы:

Похожие инструкции для NVC 200

Бренды по названию

Популярные бренды