OPERATOR’S MANUAL
PH10A-X-X
RELEASED:
7-7-00
REVISED:
(REV.
P
)
INCLUDING: OPERATION, INSTALLATION & SERVICE
1” HIGH PRESSURE DIAPHRAGM PUMP
3:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to “Model Description Chart” to match the pump material options.
637338 for air section repair (see page 6).
637339 for fluid section repair (models PH10A-XXX-XSX)(see page 4).
637339-1 for fluid section repair (models PH10A-XXX-XHX)(see page 4).
PUMP DATA
Models
see “Model Description Chart” for “-XXX”.
. . . . . . . . . . .
Pump Type
Metallic Air Operated, High Pressure,
. . . . . . . .
Double Diaphragm.
Material
see “Model Description Chart”.
. . . . . . . . . . .
Weight
94.73 lbs (42.97 kg)
. . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Air Inlet Pressure
100 psig (6.9 bar)
. . . . . . . . .
Maximum Outlet Pressure
300 psig (20.4 bar)
. . . . . . . . . .
Maximum Flow Rate (flooded inlet)
26 gpm (98.4 lpm)
. . .
Maximum Particle Size
1/8” dia. (3.2 mm)
. . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
Nitrile
10
_
to 180
_
F (-12
_
to 82
_
C)
. . . . . . . . . . . . . . . . .
PTFE
40
_
to 225
_
F (4
_
to 107
_
C)
. . . . . . . . . . . . . . . . .
Displacement / Cycle @ 100 psig
0.06 gal. (0.23 lit.)
. . . . .
Dimensional Data
see page 8.
. . . . . . . . . . . . . . . .
Noise Level @ 70 psig, 60 cpm
84.5 dB(A)
j
. . . . . .
j
The pump sound pressure levels published here have been updated to an Equivalent Continuous
Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four micro-
phone locations.
NOTICE: All possible options are shown in the chart. However, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
PH10A-XSS-XXT
1” DIAPHRAGM PUMP
Figure 1
MODEL DESCRIPTION CHART
PH10 A - X S S - X X T
Seat Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Ball Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Fluid Caps & Manifold Material
S - Stainless Steel
Fluid Connection
A - 1 - 11-1/2 NPTF - 1
B - Rp 1 (1 - 11 BSP parallel)
Diaphragm Material
T - PTFE
Hardware Material
S - Stainless Steel
Center Section Material
A - Aluminum
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276
FAX(800) 892-6276
©
201
6
CCN
99755480
arozone.com
7-15-16
L - Long Life PTFE
