infrasave IEP-1524 Скачать руководство пользователя страница 13

Страница: 13 / 18

IM110810

RD: AUGUST 2011

RL; 1A

InfraSave IEP-2024 Manual

7. MAINTENANCE INSTRUCTIONS

WARNING

Heater service should only be performed by a qualified electrician. Fail-

ure to comply could result in personal injury, death, fire and/or property
damage.

Tampering with the heater by an unqualified person will void the warranty.

WARNING

Always disconnect the heater from the electrical power supply prior to any

cleaning, maintenance or service work.

Never immerse the appliance in water! Danger to life!

CAUTION:

The Heat Lamp is fragile. Handle the heater with care so as not

to damage the Heat Lamp. Never touch the Lamp with bare fingers. Oils
from your skin will damage the Lamp.

Inspect the heater prior to each use



Clean any accumulation of dust or dirt from surfaces and in particular from the reflector

and any air openings in the heater body (refer to Cleaning section below).



Any damaged parts or components must be repaired or replaced prior to operation.

Service and Repair



Disconnect the heater from the power source prior to any servicing



Important: All repairs must be referred to qualified electrician!



Repairs carried out improperly or by an unqualified person may have serious conse-

quences for the user!



Any tampering with the appliance will invalidate the warranty.

8. CLEANING



Before cleaning - Disconnect the heater from the power supply and allow to cool.



Do not touch the Heat Lamp with your fingers - oil from your skin will damage the Lamp.



To clean the heater surface, reflector, and air inlets: Use only a dry or damp cloth or

low pressure air stream (computer ‘duster’ in a can).



Do not use any abrasive or caustic cleaning agents.



Never immerse the appliance in water! Danger to life!



If a heater is exposed to water have a qualified electrician inspect and repair the heater

prior to use.



Inspect the electrical cord for damage or fraying.



Do not operate the heater with a damaged cord



Have damaged parts replaced by a qualified electrician

Содержание IEP-1524



















Результаты поиска

Содержание IEP-1524

Отзывы:

Похожие инструкции для IEP-1524

Бренды по названию

Популярные бренды

infrasave IEP-1524, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IEP-1524

Отзывы:

Похожие инструкции для IEP-1524

Бренды по названию

Популярные бренды