Infranor Xtracontrol DC2 Скачать руководство пользователя

Страница: 70 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

10 Technical data

10.1 XtracontrolDC2

XtracontrolDC2.04

XtracontrolDC2.07

Display

WQVGA

WVGA

Across diagonals

4.3”

7” wide

Item no.

27005800

27005900

Resolution

480 x 272 pixels

800 x 480 pixels

Colours

TFT: 16.7 M (24 bits/pixel)

CPU, user memory

CPU

800 MHz ARM

CPU

Program memory (flash)

256 MB

Program memory and
data memory (RAM)

256 MB

Retain memory

100 kB (FRAM)

Dimensions and weight

Dimensions (WxHxD)

161 x 103 x 57 mm

222 x 152 x 57 mm

Weight

approx. 450 g

approx. 600 g

Operating conditions

Ambient temperature
(front side)

0 °C to 55 °C (front and rear side, in compliance with installation
requirements and operation at nominal voltage 24 V DC +5%)
50 °C at max. supply of 28.8 V DC

Relative humidity

max. 85%, non-condensing

Transport and storage

Ambient temperature

–20 °C to +70 °C

Relative humidity

max. 85%, non-condensing

Operation

Installation

integral securing clips

Certification

to product standards EN 61010-2-201, EN 61131-2

Development environment

CODESYS V3 (IEC 61131-3)

Touch operation

Touch resistive

Shock resistance

Vibration

sinusodial (EN 60068-2-6), test: Fc 10…150 Hz, 10 m/s²

Shock

15 G (approx. 150 m/s²), 11 ms duration, half-sine (EN 60068-2-27),
test: Ea

EMC, protection rating

Emitted interference

EN 61131-2; EN 61000-6-3, residential areas

Resistance to interference

EN 61131-2; EN 61000-6-2, industrial areas

Protection class

III

Protection rating

IP20, front IP54 (IP65 only with twist-lock catches tightened)

Power supply (24 V power)

Supply voltage

+24 V DC (–15 % / +20 %) SELV max. Alternating current proportion
5%

Power consumption

typ. 0.3 A, max. 3 A at +24 V DC, fused depending on the load on the
I/O

Protection against reverse

yes

Infranor GmbH

Содержание Xtracontrol DC2
























































































Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды

Infranor Xtracontrol DC2, Руководство пользователя

Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды