InfoPrint LQ-1600K Скачать руководство пользователя

Страница: 82 / 128

Chapter

Configuring The LQ-1600K Emulation With Control Codes

Set Vertical Tabs In Channels

ASCII Code

ESC b

c n1 n2 n3...n16

NUL

Hex Code

1B 62

c n1 n2 n3...n16

Dec Code

27 98

c n1 n2 n3...n16

Purpose

Assigns vertical tabs to channels selected by ESC /.

Where:

= 0 through 7

= 1 through 255

through

n16

specify the line numbers for each of the vertical

tab(s), up to a maximum of 16 tab positions in every channel,
with a maximum of eight channels. NUL must end the
sequence.

Comment

Channels are selected by ESC /. The distance of each tab stop
from TOF is the current line spacing times the number of lines
given in

If paper movement is commanded to a value of

greater than

the page length, the paper movement command is ignored.
The values of

must be in ascending order. If they are not, the

sequence up to and including the out of sequence number is
ignored. The rest of the load is processed, and skip over
perforation is ignored.

You can clear any channel by sending ESC b

NUL, where

the channel number.

The values for

must be in ascending order; a value of

less

than the previous

ends tab setting (just like the NUL code).

Skip Over Perforation

ASCII Code

ESC N

Hex Code

1B 4E

Dec Code

27 78

Purpose

Selects the number of lines (at the current line spacing) for the
paper to skip at the bottom of the perforation.

Where:

= 1 through 127,

x (current line spacing) < page length.

Comment

is the number of lines skipped between the last line printed on

one page and the first line on the next page. The actual
distance set is the product of

and the current line spacing. If

the value of

exceeds the current form length, the skip is set to

one line smaller than the form length or to 0, whichever is
greater.

Skip over perforation set by this command overrides control
panel settings. This feature is canceled by ESC O, ESC C, or
ESC C NUL.

Содержание LQ-1600K

































































































































Результаты поиска

Содержание LQ-1600K

Отзывы:

Похожие инструкции для LQ-1600K

Бренды по названию

Популярные бренды

InfoPrint LQ-1600K, Руководство программиста

Результаты поиска

Содержание LQ-1600K

Отзывы:

Похожие инструкции для LQ-1600K

Бренды по названию

Популярные бренды