InfoPrint LQ-1600K Скачать руководство пользователя

Страница: 9 / 128

Introduction

About This Manual

This manual is designed so you can quickly find the information you need to
use the LQ-1600K emulation.

This book does not explain how to operate the printer. For printer operation,
see the

InfoPrint 6500 Line Matrix Printers: User’s Manual.

Warnings and Special Information

Read and comply with all information highlighted under special headings:

WARNING

Conditions that could harm you as well as damage the equipment.

CAUTION

Conditions that could damage the printer or related equipment.

IMPORTANT

Information vital to proper operation of the printer.

NOTE:

Information affecting printer operation.

Related Product Information

Refer to the following book for printer operation:

•

InfoPrint 6500 Line Matrix Printers: User’s Manual.

Provides configuration

instructions and descriptions and troubleshooting guidelines.

Software Features

The LQ-1600K emulation software provides the following features:

•

Graphics and print quality. You can enable graphics mode and specify a
density mode (dots per inch), for either 8-pin/24-pin images.

•

Print Attributes. Characters can be bold, italic, double high, double wide,
etc.

•

Page Formatting. Commands which allow you to set line spacing, page
length, and vertical tabbing.

•

Font Typefaces. Also referred to as print modes. There are six typefaces
that can print both SBCS and DBCS characters: LQ, Near LQ, Normal,
Hi-Speed, Super Hi-Speed, and Ultra Hi-Speed.

Содержание LQ-1600K

































































































































Результаты поиска

Содержание LQ-1600K

Отзывы:

Похожие инструкции для LQ-1600K

Бренды по названию

Популярные бренды

InfoPrint LQ-1600K, Руководство программиста

Результаты поиска

Содержание LQ-1600K

Отзывы:

Похожие инструкции для LQ-1600K

Бренды по названию

Популярные бренды